Wireless Access

This community is currently in a read-only state due to a maintenance window. For more info click here
Reply
Occasional Contributor I

Configure 3rd party SFP with 7205

Aruba OS 6.5.4.8

7205 controller FIPS

 

I am unable to get a 3rd party SFP working with the Aruba 7205. I tried the "allow-unsupported-transceivers" command, it does not appear to be valid in this OS. Below you can find the port, transceiver, and port channel information. 

 

Currently their are no active lights on the SFP's, on the controller.  They are active on the other end. 

 

I did search the forums, the user guide, and the cli reference. for information with no luck. 

 

Any help would be appreciated. 

Thanks.

 

Any information would be appreciated. 

show interface gigabitethernet 0/0/2            

GE 0/0/2 is up, line protocol is down
Hardware is Gigabit Ethernet, address is  (bia )
Description: GE0/0/2 (RJ45 Connector)
Encapsulation ARPA, loopback not set
Configured: Duplex ( AUTO ), speed ( AUTO )
MTU 1500 bytes, BW is 1000 Mbit
Last clearing of "show interface" counters 1 day 0 hr 6 min 37 sec 
link status last changed 1 day 0 hr 6 min 37 sec 
    0 packets input, 0 bytes
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input error bytes, 0 CRC, 0 frame
    0 multicast, 0 unicast
    0 packets output, 0 bytes
    0 output errors bytes, 0 deferred
    0 collisions, 0 late collisions, 0 throttles
This port is TRUSTED 


 #show interface gigabitethernet 0/0/2 transceiver 

Module is SFP
Manufacturer        : FIBERXON INC.   
Part Number         : FTM-8012C-SL    , rev: 10  
S/N                 : 
Date Code           : 060811 Lot:   
Supported Modes     : 1000Base-SX, LC Connector
Wavelength          : 850 nm


 #show interface port-channel 0
Port-Channel 0 is administratively up
Hardware is Port-Channel, address is  (bia )
Description: Link Aggregate (LACP)
Spanning Tree is disabled
Switchport priority: 0
Member port: 
    GE 0/0/2, Admin is up, line protocol is down
Last clearing of "show interface" counters 1 day 0 hr 27 min 37 sec 
link status last changed 1 day 0 hr 27 min 37 sec
    0 packets input, 0 bytes
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input error bytes, 0 CRC, 0 frame
    0 multicast, 0 unicast
    0 packets output, 0 bytes
    0 output errors bytes, 0 deferred
    0 collisions, 0 late collisions, 0 throttles
Port-Channel 0 is TRUSTED

 

Highlighted

Re: Configure 3rd party SFP with 7205

Is there a reason you have a single port associated to a part channel?

 

Can you post your interface and post channel configs on both sides?

JayBee
ACDX | ACCX| CCIE (RnS/SP,DC) | ACCP | ACMP | ACSA | ACMA | CWNA | JNCIS | JNCIA
If the provided solution resolves your issue, please mark it as accepted solution to help others.
Highlighted
Occasional Contributor I

Re: Configure 3rd party SFP with 7205

The port channel was created to facilitate connectivity to two seperate vlans.   Aruba support assisted with this. 

If this is not the best procedure please let me know. 

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: