Wireless Access

Reply
Occasional Contributor II

DRT upgrade problem

Hi all,

I am working with controller 7010 and APs 334 and i faced a problem that all my APs entered Air Monitor mode evenif RF mangement for both radios are set to AP-Mode.  Then I tried to upgrade my controller's DRT version but unable to make it. I copied .dat file to flash using USB and after that i checked my flash but there is no file i copied. I appriciate if anyone can help me by showing steps i have to follow to upgrade or another way to bring my APs to AP-mode.  

            The OS version is 6.5.4.1

            DRT version: 1.0_58653

Thank you in advance


Accepted Solutions
Highlighted
MVP Guru

Re: DRT upgrade problem

The file must not be uploaded correctly. Have you tried using an alternative method instead of USB? Did you verify the file was uploaded correctly by issuing the 'dir' command? What is the country code of the controller set to? As a test, can you chance the country code and regulatory domain to a support country? 


ACMP, ACSA, ACDX #985
If my post addresses your query, give kudos:)

View solution in original post


All Replies
Highlighted
MVP Guru

Re: DRT upgrade problem

Have you followed the below?

 

https://www.arubanetworks.com/techdocs/DRT/Content/ReleaseNotes/Upgrade/DownloadableRegulatoryTable.htm

 

Also what is the regulatory domain of the controller/APs? 


ACMP, ACSA, ACDX #985
If my post addresses your query, give kudos:)
Highlighted
Occasional Contributor II

Re: DRT upgrade problem

Thank you for your immidiate reply!

Yes i followed that steps. It says file copied successfully when i copied using USB but not exsist on the flash or in regulatory file list. 

The regulatory domain profile is attached below.

Highlighted
MVP Guru

Re: DRT upgrade problem

Odd, I ususally do it via TFTP without issues. When you run the CLI 'dir' do you not see it there? Want to share the output? Also try enabling it via the CLI

 

ap regulatory activate <filename>.dat

 

What country code have you configured for the regulatory domain profile you will be using?

 

Are you certain the AP is supported in the regulatory domain you have configured?

 

https://www.arubanetworks.com/techdocs/DRT/Default.htm#ReleaseNotes/Countries/1_CountriesIntro.htm%3FTocPath%3DCountries%7C_____0


ACMP, ACSA, ACDX #985
If my post addresses your query, give kudos:)
Highlighted
Occasional Contributor II

Re: DRT upgrade problem

When i tried to activate through CLI, it says not found.

 (IP_WC1)# ap regulatory activate reg-data-1.0_73798.dat

File reg-data-1.0_73798.dat not found.

There is no my country(Ethiopia) in the list but i found in the 

Configuration > AP Group > Edit "IP_wireless" AP profile detail of 'Regulatory domain'

And check attached docs.

 

Highlighted
MVP Guru

Re: DRT upgrade problem

The file must not be uploaded correctly. Have you tried using an alternative method instead of USB? Did you verify the file was uploaded correctly by issuing the 'dir' command? What is the country code of the controller set to? As a test, can you chance the country code and regulatory domain to a support country? 


ACMP, ACSA, ACDX #985
If my post addresses your query, give kudos:)

View solution in original post

Highlighted
Occasional Contributor II

Re: DRT upgrade problem

Thank you so much Craig Syme I have changed a country code of controller set to on regulatory domain to a supported country and it worked! Thank you again!
Highlighted
MVP Guru

Re: DRT upgrade problem

You’re welcome :)

Sent from my iPhone

ACMP, ACSA, ACDX #985
If my post addresses your query, give kudos:)
Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: