Wireless Access

last person joined: yesterday 

Access network design for branch, remote, outdoor, and campus locations with HPE Aruba Networking access points and mobility controllers.
Back to discussions
Expand all | Collapse all

Master / Local LAB, ver_6.4.3.9, AP's config incorecct

This thread has been viewed 0 times

  • 1.  Master / Local LAB, ver_6.4.3.9, AP's config incorecct

    Posted Jun 22, 2016 04:54 AM

    Hi,every one, I am a new about aruba,

    Here is my Master / Local LAB ,

    Master ver : ArubaOS (MODEL: Aruba6000), Version 6.4.3.9   IP : 192.168.71.217

    Local ver : ArubaOS (MODEL: Aruba7210), Version 6.4.3.9    IP : 192.168.71.218

    All Switches
    ------------
    IP Address      Name       Location          Type    Model      Version        Status  Configuration State  Config Sync Time (sec)  Config ID
    ----------      ----       --------          ----    -----      -------        ------  -------------------  ----------------------  ---------
    192.168.71.217  Aruba6000  Building1.floor1  master  Aruba6000  6.4.3.9_55230  up      UPDATE SUCCESSFUL    0                       29
    192.168.71.218  Aruba7210  Building1.floor1  local   Aruba7210  6.4.3.9_55230  up      UPDATE SUCCESSFUL    2                       29

    Total Switches:2

    --------------------------------

    When I set an AP-105 use remote AP mode, and I config the LMS profile , there is an strange thing about the ap config,

    -------------------------------

    here is the ap database display

    AP Database
    -----------
    Name         Group            AP Type  IP Address    Status         Flags  Switch IP       Standby IP
    ----         -----            -------  ----------    ------         -----  ---------       ----------
    My-test-001  Group-Jace_test  105      10.10.217.24  Up 1h:30m:40s  Rc2    192.168.71.217  0.0.0.0

     

    ===============

    here is my group config

    AP group "Group-Jace_test"
    --------------------------
    Parameter                                Value
    ---------                                -----
    Virtual AP                               VAP-Mydot1x
    802.11a radio profile                    default
    802.11g radio profile                    default
    Ethernet interface 0 port configuration  default
    Ethernet interface 1 port configuration  default
    Ethernet interface 2 port configuration  shutdown
    Ethernet interface 3 port configuration  shutdown
    Ethernet interface 4 port configuration  shutdown
    AP system profile                        apsys_LMStest
    VoIP Call Admission Control profile      default
    802.11a Traffic Management profile       N/A
    802.11g Traffic Management profile       N/A
    Regulatory Domain profile                default
    RF Optimization profile                  default
    RF Event Thresholds profile              default
    IDS profile                              default
    Mesh Radio profile                       default
    Mesh Cluster profile                     N/A
    Provisioning profile                     N/A
    AP authorization profile                 N/A

    ================

    I set the group's ap-system file use "apsys_LMStest" , but when I check the ap config, it shows different

    (Aruba6000) #show ap config ap-name My-test-001

    Configuration for AP name "My-test-001" AP group "Group-Jace_test"
    ------------------------------------------------------------------
    Parameter                                                                    802.11g                         802.11a                Source
    ---------                                                                    -------                         -------                ------
    RF Band                                                                      g                               g                      ap system-profile "apsys_default"
    RF Band for AM mode scanning                                                 all                             all                    ap system-profile "apsys_default"
    Native VLAN ID                                                               1                               1                      ap system-profile "apsys_default"
    Tunnel Heartbeat Interval                                                    1                               1                      ap system-profile "apsys_default"
    Session ACL                                                                  ap-uplink-acl                   ap-uplink-acl          ap system-profile "apsys_default"
    SNMP sysContact                                                              N/A                             N/A                    ap system-profile "apsys_default"
    LED operating mode (11n/11ac APs only)                                       normal                          normal                 ap system-profile "apsys_default"
    LED override                                                                 Disabled                        Disabled               ap system-profile "apsys_default"
    Driver log level                                                             emergencies                     emergencies            ap system-profile "apsys_default"
    SAP MTU                                                                      N/A                             N/A                    ap system-profile "apsys_default"
    RAP MTU                                                                      1200 bytes                      1200 bytes             ap system-profile "apsys_default"
    LMS IP                                                                       192.168.71.217                  192.168.71.217         ap system-profile "apsys_default"
    Backup LMS IP                                                                192.168.71.218                  192.168.71.218

     

     

    ===================

    so I can't move the AP to Local-controller

    could anyone provide some suggestion for me,

    Thank you !



  • 2.  RE: Master / Local LAB, ver_6.4.3.9, AP's config incorecct

    Posted Jun 23, 2016 05:12 AM

    You applied and saved configuration afterwards?

     

    Does it behave the same way if you apply a new profile elsewhere? 



  • 3.  RE: Master / Local LAB, ver_6.4.3.9, AP's config incorecct

    Posted Jun 23, 2016 05:33 AM

    Hi, thank you for the reply

     

    I create a new ap-system profile, and change the AP-Group's sp-system profile.

    write memory and check the Master / Local AP configuration.( the config was synconized to local)

    then I reboot the AP , it still use the wrong config .

     

    which command should I use to toublesoot ,

    show datapath or something ?

     

    thank you !