This is what i get if i reboot the AP and see through console.
APBoot 1.2.7.4 (build 32721)
Built: 2012-03-08 at 11:33:21
Model: AP-9x
CPU: AR7242 revision: 1
Clock: 390 MHz, DDR rate: 390 MHz, Bus clock: 195 MHz
DRAM: 64 MB
POST1: passed
Copy: done
Flash: 16 MB
PCI: scanning bus 0 ...
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 168c 002a 00002 01 10000004 00000000 00000000 00000000
Net: eth0
Radio: ar9280#0
Hit <Enter> to stop autoboot: 0
Checking image @ 0xbf100000
Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
ELF file is 32 bit
Loading .text @ 0x80e00000 (3755944 bytes)
Loading .data @ 0x81194fb0 (32 bytes)
Clearing .bss @ 0x81194fd0 (16 bytes)
## Starting application at 0x80e00000 ...
Uncompressing...................................
Aruba Networks
ArubaOS Version 6.1.3.1 (build 32786 / label #32786)
Built by p4build@cartman on 2012-03-12 at 23:43:35 PDT (gcc version 4.3.3)
CPU Rev: 1101
72x CPU
Flash variant: 16M
Cache parity protection disabled
Using 195.000 MHz high precision timer. cycles_per_jiffy=390000
Memory: 58020k/65536k available (1849k kernel code, 7460k reserved, 682k data, 2
940k init, 0k highmem)
available.
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=8388608,origSize=12301312
LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com> ...........................
................................................................................
................................................................................
.
Returning IRQ 48
AR7240 GPIOC major 0
wdt: registered with refresh
Enabling Watchdog
Talisker RSSI LED initialization
Creating 1 MTD partitions on "ar7240-nor0":
0x00000000-0x01000000 : "flash"
i2c /dev entries driver
i2c-talisker: using default base 0x18040000
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
Starting Kernel DES KAT ...Completed Kernel DES KAT
Starting Kernel AES KAT ...Completed Kernel AES KAT
Domain Name: arubanetworks.com
No panic info available
apfcutil -c RAP: OK...................
AG7240: Length per segment 1536
AG7240: Max segments per packet 1
AG7240: Max tx descriptor count 40
AG7240: Max rx descriptor count 252
AG7240: fifo cfg 3 01f00140
AG7240CHH: Mac address for unit 0
AG7240CHH: d8:c7:c8:cf:5c:ae
ATHRSF1_PHY: Port 0, Neg Success
ATHRSF1_PHY: unit 0 phy addr 0 <6>AP xml model 43, num_radios 1 (jiffies 4287)
init_asap_mod: installation:1
radio 0: band 2 ant 0 max_ssid 16
setting bond0 as bridge child
setting gre0 as split child
USB not provisioned
Starting watchdog process...
Got all network params from APboag7240_ring_alloc Allocated 640 at 0x80402800
ot env. Skippingag7240_ring_alloc Allocated 4032 at 0x810c3000
Virian MDC CFG Value ==> 4
Setting PHY...
ATHRSF1_PHY: Port 0, Neg Success
ATHRSF1_PHY: unit 0 phy addr 0 Not enabling interrupts in AR7242 yet...
ADDRCONF(NETDEV_UP): bond0: link is not ready
DHCP
192.168.10.201 255.255.255.0 192.168.10.1
Running ADP...AG7240: enet unit:0 is up...
RGMii 100Mbps full duplex
AG7240: done cfg2 0x7115 ifctl 0x10000 miictrl
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
Done. Master is 192.168.10.200
Starting Webserver
bind: Transport endpoint is not connected
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Right
s Reserved
ath_rate_atheros: Aruba Networks Rate Control Algorithm
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_spectrum: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserve
d
ath_pci: 0.9.4.5 (Atheros/multi-bss)
wifi0: Base BSSID d8:c7:c8:75:ca:e0, 16 available BSSID(s)
bond0 address=d8:c7:c8:cf:5c:ae
br0 address=d8:c7:c8:cf:5c:ae
wifi0: AP type AP-93, radio 0, max_bssids 16
wifi0: Atheros 9280: mem=0x10000000, irq=48 hw_base=0xb0000000
Starting FIPS KAT ... Completed FIPS KAT
shutting down watchdog process (nanny will restart it)...
<<<<< Welcome to the Access Point >>>>>
Please advice if the steps i did to install the AP was correct .
also i noticed after provisioning it says up and after a while i cannot see it as AP and it shows up as AM and goes down.