Good morning to all.
I'm having a problem with a newly evaluation VMC in standalone mode.
I applied all licenses to VMC in order to control APs as you can see in screenshot "forum".
I connected 3 IAP-305 (RW) to same subnet and converted them to Campus mode. Also configured controller IP address (vmc) when I converted the aps.
On the controller, I approved the APs but they won't take the licenses applied over VMC.
Attached you will find screenshots of what i'm talking about and next, I will post some cli info.
login as: admin
admin@172.30.31.67's password:
NOTICE
NOTICE -- This server has active licenses that will expire in 24 days
NOTICE
NOTICE -- See 'show license' for details.
NOTICE
(ArubaMC-POC-) [mynode] #show log system 10
Oct 29 17:26:37 KERNEL(AP 2@172.30.31.63): [ 19.021431] uol_init_driver:261 HW offload not applicable, AP will use cutting through path!
Oct 29 17:26:39 :303022: <WARN> |AP AP 1@172.30.31.62 nanny| Reboot Reason: AP rebooted Tue Oct 29 17:25:34 -03 2019; SAPD: Reboot requested by controller
Oct 29 17:26:39 :303022: <WARN> |AP AP 3@172.30.31.64 nanny| Reboot Reason: AP rebooted Tue Oct 29 17:25:34 -03 2019; SAPD: Reboot requested by controller
Oct 29 17:26:39 :303022: <WARN> |AP AP 2@172.30.31.63 nanny| Reboot Reason: AP rebooted Tue Oct 29 17:25:34 -03 2019; SAPD: Reboot requested by controller
Oct 29 17:27:22 :305038: <5654> <WARN> |stm| No available license type VMC for AP AP 1
Oct 29 17:27:22 :305038: <5654> <WARN> |stm| No available license type VMC for AP AP 3
Oct 29 17:27:22 :305038: <5654> <WARN> |stm| No available license type VMC for AP AP 2
Oct 29 17:27:29 :305038: <5654> <WARN> |stm| No available license type VMC for AP AP 1
Oct 29 17:27:29 :305038: <5654> <WARN> |stm| No available license type VMC for AP AP 3
Oct 29 17:27:29 :305038: <5654> <WARN> |stm| No available license type VMC for AP AP 2
(ArubaMC-POC-) [mynode] #show license
License Table
-------------
Key Installed Expires(Grace period expiry) Flags Service Type
--- --------- ---------------------------- ----- ------------
AN1WFkW6-KG35wbie-l5qyyzvU-P8U7+iVM-22JpV6Rb-HU2ohm0I-aOBxJmOE-vbv928VL-JIgC03oR-V1E 2019-10-23 17:41:19[1] 2019-11-22 17:41:19 E MC-VA-US: 1000
Y/DkmMvM-dIqMJWEN-FzuN/FV/-ipw3Job2-yAdmuO3F-qrONjEwi-0FTPMyhj-pKKzC1sg-8b+vQqh9-Zxs 2019-10-23 17:42:26[1] 2019-11-22 17:42:26 E Access Points: 2048
FlYV1sNx-Rx+tj1Cx-my/h1CRs-eU3/AwlA-rgcIM+sW-0yV61qY/-vuSen86P-s5jRJp91-xm13+kHP-/8o 2019-10-23 17:43:34[1] 2019-11-22 17:43:34 E Next Generation Policy Enforcement Firewall Module: 2048
MnBzRpe0-e+jqwKlD-ZGoyDmVY-RfW16SgG-IKqGogfb-oudVJtGO-HDHMJIyZ-AOKOklI+-l18GvwkT-Zmg 2019-10-23 17:44:16[1] 2019-11-22 17:44:16 E RF Protect: 2048
3DLoOabI-DYjGSOp9-OI+2/NFz-k5OhnrFT-1g0qsBLy-Va8NtGy1-keujMsFV-xbn0do2b-WHathbjA-oqg 2019-10-29 16:13:42[1] 2019-11-28 16:13:42 E MM-VA: 10000
License Entries: 5
Flags: A - auto-generated; E - enabled; S - Subscription; R - reboot/activation key required to activate; D - Not enabled on license client
Note: Time under 'Installed' for Subscription licenses is the license generation time.
(ArubaMC-POC-) [mynode] #show switches
All Switches
------------
IP Address IPv6 Address Name Location Type Model Version Status Configuration State Config Sync Time (sec) Config ID
---------- ------------ ---- -------- ---- ----- ------- ------ ------------------- ---------------------- ---------
172.30.31.67 None ArubaMC-POC- Building1.floor1 standalone ArubaMC-VA 8.4.0.4_71183 up UPDATE SUCCESSFUL 0 7
Total Switches:1
(ArubaMC-POC-) [mynode] #show ap database
AP Database
-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP
---- ----- ------- ---------- ------ ----- --------- ----------
AP 1 AP-poc- 305 172.30.31.62 Up 1m:56s 2IL 172.30.31.67 0.0.0.0
AP 2 AP-poc- 305 172.30.31.63 Up 1m:55s 2IL 172.30.31.67 0.0.0.0
AP 3 AP-poc- 305 172.30.31.64 Up 1m:55s 2IL 172.30.31.67 0.0.0.0
Flags: 1 = 802.1x authenticated AP use EAP-PEAP; 1+ = 802.1x use EST; 1- = 802.1x use factory cert; 2 = Using IKE version 2
B = Built-in AP; C = Cellular RAP; D = Dirty or no config
E = Regulatory Domain Mismatch; F = AP failed 802.1x authentication
G = No such group; I = Inactive; J = USB cert at AP; L = Unlicensed
M = Mesh node
N = Duplicate name; P = PPPoe AP; R = Remote AP; R- = Remote AP requires Auth;
S = Standby-mode AP; U = Unprovisioned; X = Maintenance Mode
Y = Mesh Recovery
c = CERT-based RAP; e = Custom EST cert; f = No Spectrum FFT support
i = Indoor; o = Outdoor; s = LACP striping; u = Custom-Cert RAP; z = Datazone AP
p = In deep-sleep status
Total APs:3
(ArubaMC-POC-) [mynode] #show ap
active Show APs currently registered or have some clients
terminating (in cluster) on this switch
allowed-channels Show the set of allowed channels
allowed-max-EIRP Show max EIRP setting per country per AP type
amon Show AMON message information
analytics Recommendations from Analytics
ap-cert-mgr Show contents of /tmp/ap_cert_mgr_debug_log for an AP
ap-group Show contents of AP's group
arm Show ARM Information
assoc-throttle-counters Show counters related to association request throttling.
association Show Association table for an AP
authorization-profile Show an AP Authorization profile
band-steering-clients Show Band Steering State
blacklist-clients Show all clients being DoSed
blacklist-protected Show all clients that are currently protected against
further traffic steering related DoS actions for a
period of time
blacklist-time Show the amount of blacklist time of the STA when it is
blacklisted in between disconnection and user-timeout
ble-database Show BLE APB information collected by BLE relay
ble-ibeacon-info Show AP's BLE radio iBeacon parameters
bss-table Show bssids of all APs registered on this switch
(ArubaMC-POC-) [mynode] #show ap database lo
local Show only APs on this switch
long Show additional columns
(ArubaMC-POC-) [mynode] #show ap database long
AP Database
-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP Wired MAC Address Serial # Port FQLN Outer IP User
---- ----- ------- ---------- ------ ----- --------- ---------- ----------------- -------- ---- ---- -------- ----
AP 1 AP-poc- 305 172.30.31.62 Rebooting 2IL 172.30.31.67 0.0.0.0 90:4c:81:ca:1f:c8 CNG9JSSCK6 N/A N/A N/A
AP 2 AP-poc- 305 172.30.31.63 Rebooting 2IL 172.30.31.67 0.0.0.0 90:4c:81:ca:0a:20 CNG9JSSCHC N/A N/A N/A
AP 3 AP-poc- 305 172.30.31.64 Rebooting 2IL 172.30.31.67 0.0.0.0 90:4c:81:c9:fc:30 CNG9JSSCL8 N/A N/A N/A
Flags: 1 = 802.1x authenticated AP use EAP-PEAP; 1+ = 802.1x use EST; 1- = 802.1x use factory cert; 2 = Using IKE version 2
B = Built-in AP; C = Cellular RAP; D = Dirty or no config
E = Regulatory Domain Mismatch; F = AP failed 802.1x authentication
G = No such group; I = Inactive; J = USB cert at AP; L = Unlicensed
M = Mesh node
N = Duplicate name; P = PPPoe AP; R = Remote AP; R- = Remote AP requires Auth;
S = Standby-mode AP; U = Unprovisioned; X = Maintenance Mode
Y = Mesh Recovery
c = CERT-based RAP; e = Custom EST cert; f = No Spectrum FFT support
i = Indoor; o = Outdoor; s = LACP striping; u = Custom-Cert RAP; z = Datazone AP
p = In deep-sleep status
Total APs:3
(ArubaMC-POC-) [mynode] #
Thanks in advance my friends.
Best regards.
Gonzalo.