Wireless Access

Reply
New Contributor

Trying to factory reset used AP 105

I am having trouble reseting ap 105, I have done the following 

apboot> factory_reset
apboot> purgeenv
apboot> save
apboot> boot

However I am getting this message after. 

APBoot 1.0.9.12 (build 22797)
Built: 2009-11-04 at 15:53:54

Model: AP-10x
CPU: AR7161 revision: A2
Clock: 680 MHz, DDR clock: 340 MHz, Bus clock: 170 MHz
DRAM: 128 MB
POST1: passed
Copy: done
Flash: 16 MB
PCI: scanning bus 0 ...
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 168c 0029 00002 01 10000000 00000000 00000000 00000000
01 00 168c 0029 00002 01 10010000 00000000 00000000 00000000
Net: eth0
Radio: ar922x#0, ar922x#1

Hit <Enter> to stop autoboot: 0
apboot> <INTERRUPT>
apboot> factory_reset
Clearing state... Erasing flash... .done
Erased 1 sectors
done
Purging environment... Un-Protected 1 sectors
.done
Erased 1 sectors
Writing
done
apboot> pureenv<INTERRUPT>
apboot> purgeenv
Un-Protected 1 sectors
.done
Erased 1 sectors
Writing
apboot> <INTERRUPT>
apboot> save
Saving Environment to Flash...
Un-Protected 1 sectors
.done
Erased 1 sectors
Writing
apboot> boot
Checking image @ 0xbf100000
Invalid image format version: 0xffffffff
eth0: down
DHCP broadcast 1
eth0: down
DHCP broadcast 2
eth0: down
DHCP broadcast 3
eth0: down
DHCP broadcast 4
eth0: down
DHCP broadcast 5
eth0: down

Retry count exceeded; starting again
eth0: down
DHCP broadcast 1
eth0: down
DHCP broadcast 2
eth0: down
DHCP broadcast 3
eth0: down
DHCP broadcast 4
eth0: down
DHCP broadcast 5
eth0: down

Retry count exceeded; starting again
eth0: down
DHCP broadcast 1
eth0: down
DHCP broadcast 2
eth0: down
DHCP broadcast 3
eth0: down
DHCP broadcast 4
eth0: down
DHCP broadcast 5
eth0: down

Retry count exceeded; starting again
eth0: down
DHCP broadcast 1
eth0: down
DHCP broadcast 2
eth0: down
DHCP broadcast 3
eth0: down
DHCP broadcast 4
eth0: down
DHCP broadcast 5
eth0: down




Guru Elite

Re: Trying to factory reset used AP 105

It looks like your instant AP is not getting an ip address.


*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.3 User Guide
InstantOS 8.3 User Guide
Airheads Knowledgebase
Airheads Learning Videos
New Contributor

Re: Trying to factory reset used AP 105

What would I do in that case since my ap is not getting an IP address

Guru Elite

Re: Trying to factory reset used AP 105

You would need to plug it into a port that provides DHCP.


*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.3 User Guide
InstantOS 8.3 User Guide
Airheads Knowledgebase
Airheads Learning Videos
Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: