I am trying to configure a VRRP between a 620 and a 3200. Master-Master (no redundancy).
Testing....
I setup my VRRP on my master first
vrrp 100
priority 110
authentication aruba123
ip address 172.30.50.78
description "wlc-1"
vlan 1
no shutdown
!
(dnoc-wlc-1.rdlab.dv) (config-vrrp)# show vrrp
Virtual Router 100:
Description wlc-1
Admin State UP, VR State MASTER
IP Address 172.30.50.78, MAC Address 00:00:5e:00:01:64, vlan 1
Priority 110, Advertisement 1 sec, Preemption Disable Delay 0
Auth type PASSWORD, Auth data: ********
tracking is not enabled
It comes up as Master, VIP is pingable (50.78)
I then configure it on the backup-master and it becomes Master as well
vrrp 100
priority 90
authentication aruba123
ip address 172.30.50.78
description "wlc-2"
vlan 1
no shutdown
!
(dnoc-wlc-2.rdlab.dv) (config) #show vrrp
Virtual Router 100:
Description wlc-2
Admin State UP, VR State MASTER
IP Address 172.30.50.78, MAC Address 00:00:5e:00:01:64, vlan 1
Priority 90, Advertisement 1 sec, Preemption Disable Delay 0
Auth type PASSWORD, Auth data: ********
tracking is not enabled
In 'show log system' I see the following for both controllers:
WLC-1
Mar 27 11:13:34 :313329: <DBUG> |fpapps| VRRP: Sending Advertisement for vrid 100
Mar 27 11:13:38 :307048: <DBUG> |cfgm| Got a message from 8231:5010
Mar 27 11:13:38 :307050: <DBUG> |cfgm| Received a IPSEC CFG Message
Mar 27 11:13:38 :307219: <DBUG> |cfgm| Sending the IPSEC Configuration
Mar 27 11:13:39 :313329: <DBUG> |fpapps| VRRP: Sending Advertisement for vrid 100
Mar 27 11:13:42 :301278: <INFO> |snmp| Authentication failure, bad community string
Mar 27 11:13:42 :301246: <NOTI> |snmp| 201 SNMP Authentication Failed for Management station 172.30.49.19
Mar 27 11:13:43 :313329: <DBUG> |fpapps| VRRP: Sending Advertisement for vrid 100
WLC-2
Mar 27 11:13:46 :313329: <DBUG> |fpapps| VRRP: Sending Advertisement for vrid 100
Mar 27 11:13:49 :307048: <DBUG> |cfgm| Got a message from 8231:5010
Mar 27 11:13:49 :307050: <DBUG> |cfgm| Received a IPSEC CFG Message
Mar 27 11:13:49 :307219: <DBUG> |cfgm| Sending the IPSEC Configuration
Mar 27 11:13:50 :313329: <DBUG> |fpapps| VRRP: Sending Advertisement for vrid 100
Mar 27 11:13:54 :300197: <DBUG> |licensemgr| __license_timer
Mar 27 11:13:54 :300149: <DBUG> |licensemgr| __license_expire: executing cmd SELECT id, skey, installed, expires, complete, enabled, icount, inactive from licenseinfo_new
Mar 27 11:13:54 :300197: <DBUG> |licensemgr| __license_remove_cli_warning: removing warning file
Mar 27 11:13:54 :300197: <DBUG> |licensemgr| __license_publish_expiry: not publishing update value unchanged [-1
Mar 27 11:13:55 :313329: <DBUG> |fpapps| VRRP: Sending Advertisement for vrid 100
Both of them are sending advertisements but none of them are responding....any ideas?
#3200