Search the Community
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
30,000 results
Sorted by:
05-24-2014
08:32 PM
I'm getting this message when trying to run a conversion of 10 IAP 115's. While researching this I'm finding older threads that mention the controller needing to run 6.1. All of t...
08-24-2016
06:00 PM
Can not get an Aruba 325 AP to convert from IAP to Campus AP. I have done both the instant UI and CLI commands. In both cases the AP appears like it is converting but I never see it at m...
08-12-2018
08:23 PM
...ontroller and starts the conversion process. About 2 to 3 minutes later, an dialog box appears 'Retrieve image failed, please save the log in the popup window". I am using the controller's external VRRP IP a...
Show results in replies (9)
-
...ole was re-added, I was able to successfully provision the RAP and establish connectivity.
-
...After I moved the RAP to another subnet, the conversion worked like normal.
-
...ddress to the ACL. Both ports 4500 and 500 are allowed. When I create the static nat to the a...
-
Under the existing 3400 RAP Controller(6.4.4.16), the process works without an issue. The conversion...
-
Is there a firewall between the AP And the VRRP address? Try the static NAT to the actual i...
-
loopback is not required, but a loopback should share a subnet with one of the routable VLANs on t...
-
Thanks for the recommendation. On the non-working rap controller, I matched 99% of the settings. t...
-
...ecessary for this to work.
-
...n the working rap controller. On the non-working controller, ALG protocol is set to tftp. Is that a factor?
03-18-2015
07:29 AM
i am trying to convert iap-93 to cap but it fails i see it cannot connect to port 21 in error logs any help appreciated. show vpn status profile n...
Show results in replies (9)
-
HI, For converting IAP to CAP or IAP to RAP we have min image version criteria. I will s...
-
HI, In order to convert an IAP to RAP, Controller should have minimum 6.1 Image version a...
-
Hi, These IAP's were previously converted to CAP and was working perfectly. We then c...
-
Hi, Please upgrade the IAP version to 4.1 or higher.
-
Both the AOS of the controller and IAP is above 6.1 also control plane security is disabled on t...
-
...ersion: 6.3.1.8-4.0.0.8_46401 Upgrade the IAP to 6.3.1.8-4.1.x.x or above &n...
-
I am running aos 6.3.1.6 on the controller and on the IAP-93 aos is greater than the one on t...
-
Looks like your controller doesn't have the required code. What version of AOS is running on your c...
-
There is some confusion added in that iAP code has two version numbers to the uninitiated: 6.3.x.x...
08-15-2019
09:02 AM
Hello, My apologies if this is old news, but I recieved an IAP-315 and when I try to upgrade firmware in the gui I get the error. I was on 6.5.x out of the box and m...
Labels:
09-15-2016
12:38 PM
Hi All, I'm having an issue converting an IAP 225 to CAP on AOS 8.0.0.0 7005 controller. Where is the table that lists minimum supported IAP version in case that is my problem? T...
Labels:
07-26-2018
10:33 PM
Hi, I have 70 IAP all new in the box, we want to deploy them at one of our branch offices as a controller base. is there a way to convert them to from IAP to CAP without creating IAP c...
Show results in replies (8)
-
...ompletely) - the extra IAPs will swarm to join the Instants AP master; when conversion takes p...
-
....com/t5/Controller-less-WLANs/IAP-to-rap-apboot-conversion/ta-p/176836 It should work a...
-
.../t5/Controller-less-WLANs/IAP-to-rap-apboot-conversion/ta-p/176836 It should work also on IAP...
-
...bsp; Also if the IP of the master / switch is saved directly into the AP, am I correct in t...
-
@Craig Syme wrote: Is there a reason you want to complete this before creating a cluster? W...
-
Hi Which model of AP? You can do this quicker by concole. 1....
-
Is there a reason you want to complete this before creating a cluster? When the IAP's have c...
-
@Craig Syme wrote: Is there a reason you want to complete this before creating a cluster? W...
05-11-2017
12:10 AM
...t says 'downloading information form controller'. After a while it shows us the message in Instant: - Retrieve image failed, please save the log in the popup window. AP will reboot in 15 m...
Show results in replies (9)
-
...river probe failed for RC0:-1 [ 0.429137] msm_pcie: probe of 80000.qcom,pcie failed...
-
...etween RAP and MC btw for image updates Reboot AP, convert again,. Boom - Correct inner IP and conversion...
-
...onvert it fails with an "failed to retrieve image" error. Daniel
-
...ost. Error: failed to retrieve image But I can ping the controller from AP. And as I said, t...
-
Hi; To see the registry, try to see if it is possible that you have blocked the p...
-
If the controller is running 8.2.1.0, I have no idea. Could you try to upgrade IAP to latest v...
-
Do you see any errors in the logs on the CLI of the controller or IAP? Are there any firewalls b...
-
I put a factory default AP of the same type (ap305) on the port and it came up as instant. Then d...
-
I was having the same problem with a few cases of IAP325's. My Controller running version 6.5.4.9 a...
03-28-2017
04:24 PM
...tp://sap:*password*@x.x.x.x/e500.ari (try: 3) => `e500.ari' Connecting to x.x.x.x:21... failed: Connection timed out. Giving up. Error: failed to retrieve image cleaning up d...
Labels:
Show results in replies (4)
-
...heck the following output on the IAP while conversion process is ongoing: show datapath s...
-
On the face of it, it looks like ftp is blocked between the IAP and the controller.
-
OK, let me upgarde it to a newer version and I'll check the output of the convertion and I'll let y...
-
Thanks Nitesh Singala, I just installed the same version that I have on the Controller into the IAP...
07-25-2013
08:23 AM
We've been deploying IAP's & CAP's for a while (as well as utilizing Activate). Is it possible to use local DHCP option for "InstantAP" to trigger CAP conversion? This would a...
