Hello,
I have an Aruba 303 AP that once was used in a controller (mobility master) enviorment.
I am booting it in a LAB with no controller and keep getting this "runnig ADP..." and after a minute it is getting "Running ADP /tmp/master No such file or directory".
I did a factory_reset with console
and try to do with the actual bottun but still see the old AP name in IP_Scann and cannot boot it.
any help please.
Hit <Enter> to stop autoboot: 0
Checking image @ 0x0
Invalid image format version: 0x0
Checking image @ 0x2000000
Copying image from 0x84000000
Image is signed; verifying checksum... passed
SHA2 Signature available
Signer Cert OK
Policy Cert OK
RSA signature verified using SHA2.
Uncompressing Kernel Image ... OK
[ 0.000000]
[ 0.000000] Aruba Networks
[ 0.000000] ArubaOS Version 6.5.2.0 (build 58369 / label #58369)
[ 0.000000] Built by p4build@naxos on 2017-02-10 at 02:04:23 PST (gcc version 4.6.3)
[ 0.000000]
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.039270] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.087818] i2c-gpio driver registered
[ 5.825797] 3 ofpart partitions found on MTD device 7980000.qcom,nand
[ 5.890448] Creating 3 MTD partitions on "7980000.qcom,nand":
[ 5.959194] 0x000000000000-0x000002000000 : "aos0"
[ 6.058953] 0x000002000000-0x000004000000 : "aos1"
[ 6.145975] 0x000004000000-0x000008000000 : "ubifs"
[ 6.291403] m25p80 spi0.0: found mx25r3235f, expected n25q128a11
[ 6.446916] Found AT97SC3203 on i2c_1.8
[ 6.488529] Key type dns_resolver registered
[ 6.531456] Registering SWP/SWPB emulation handler
[ 8.253536] TZ dump found for reboot
[ 8.321331]
Starting Kernel SHA1 KAT ...
[ 8.355805] Completed Kernel SHA1 KAT
[ 8.402696] Starting Kernel HMAC-SHA1 KAT ...
[ 8.452852] Starting Kernel DES KAT ...[ 8.498567] Completed Kernel DES KAT
[ 8.542288] Starting Kernel AES KAT ...
[ 8.586078] Completed Kernel AES KAT
[ 8.586078]
[ 8.649703] Starting Kernel AESGCM KAT ...
[ 8.696391] Completed Kernel AESGCM KAT
[ 8.745739] Completed Kernel HMAC-SHA1 KAT
AP-type has_ble_support: ONBOARD.
Domain Name: arubanetworks.com
No panic info available
Writing /dev/ttyMSM1 into /tmp/ble_port
Enabling ble_daemon via nanny
[ 15.621676] edma module_init
[ 16.546897] drvlog_mod: module license 'Proprietary' taints kernel.
[ 16.609486] Disabling lock debugging due to kernel taint
Starting watchdog process...
Getting an IP address...
[ 21.684159] bond0: GMAC Link is up with phy_speed=1000
10.0.0.4 255.255.255.0 10.0.0.138
Running ADP...
( And after a minute or so)
Running ADP...cat: /tmp/master: No such file or directory
Done. Master is
killall: nanny: no process killed
killall: sapd: no process killed
Sending SIGKILL to all processes.
Unmounting UBIFS completed.
Please stand by while rebooting the system.
[ 98.593041] reboot: Restarting system