Wired Intelligent Edge

I had an issue previously where AP305C did not connect at AT power from HP Procurve 2920

The solution was:

https://ewouddenbreeijen.nl/net-posts/poe-issues-aruba-switches-and-powered-device/

no lldp config <interface(s)> dot3TlvEnable poeplus_config

I now have same APs connected to Aruba 6300M (which is running very different OS, Aruba CX, so the commands are totally different)

Same issue:

MB-LG-DH-Mid#sh system led
Brightness configuration:       soft

System LED status:
No  Led       Colour                        Blinking
---------------------------------------------------------
1   Power     Off                           No blinking
2   Status    White                         Slow blinking

https://extreme-networks.my.site.com/ExtrArticleDetail?an=000072411

White, Slow-blinking: The device has a CAPWAP connection to ExtremeCloud IQ, but is operating on 802.3af power instead of 802.3at power.

MB-LG-DH-Mid#sh system power mode
System Power Mode:   Auto/AF

MAX tx/rx chains:    4X4
MAX wifi0 tx power:  20dbm
MAX wifi1 tx power:  20dbm
USB Port:            On
GE                   Status
---------------------------
Eth0                 UP

The PoE info from the switch

sw-flowerroom-6300(config)# sh running-config interface 1/1/10
interface 1/1/10
    no shutdown
    no routing
    vlan trunk native 501
    vlan trunk allowed 21,50,100,110,120,130,140,150,300
    power-over-ethernet assigned-class 4
    exit
sw-flowerroom-6300(config)# sh power-over-ethernet 1/1/10

Status and Configuration Information for port 1/1/10

  Power Enable           : Yes            PD signature             : single
  PoE Port Status        : delivering     PD Type                  : Type2
  Alloc-by Configured    : usage          Alloc-by Actual          : lldp-dot3
  User Profile Priority  : N/A            Port Config Priority     : Low
  Port Priority          : low            Pre-std Detect           : Disabled
  PD Requested Class     : Class4         PSE Assigned Class       : Class4
  Fault Status           : None           User set Assigned Class  : class4
  PD Class Override      : Disabled       Power Pairs Configured   : alt-a-and-alt-b
                                          Power Pairs Applied      : alt-a-and-alt-b

PoE Counter Information

  Over Current Cnt       : 0              MPS Absent Cnt           : 3
  Power Denied Cnt       : 0              Short Cnt                : 0

Power Information

  PSE Voltage            :  54.48 V       PSE Reserved power       :  16.80 W
  PD Current Draw        :   0.10 A       PD Power Draw            :   5.45 W
  PD Average Power Draw  :   4.88 W       PD Peak Power Draw       :   5.45 W


LLDP Information

  MED Override             : Disabled
  MED Priority             : Critical
  PSE TLV Configured       : dot3/med
  PSE TLV Sent Type        : dot3
  PD TLV Sent Type         : dot3
  PSE Allocated Power Value: 15.40 W
  PD Requested Power Value : 15.40 W

Any idea how to make the two of them living in harmony?

Thanks

------------------------------
spgsitsupport
------------------------------

As there were no takers here

The solution is very simple

On interface in question use:

power-over-ethernet allocate-by class

MB-LG-DH-Mid#sh system ledBrightness configuration:       softSystem LED status:No  Led       Colour                        Blinking---------------------------------------------------------1   Power     Off                           No blinking2   Status    White                         Slow blinking

MB-LG-DH-Mid#sh system power modeSystem Power Mode:   Auto/AFMAX tx/rx chains:    4X4MAX wifi0 tx power:  20dbmMAX wifi1 tx power:  20dbmUSB Port:            OnGE                   Status---------------------------Eth0                 UP

sw-flowerroom-6300(config)# sh running-config interface 1/1/10interface 1/1/10    no shutdown    no routing    vlan trunk native 501    vlan trunk allowed 21,50,100,110,120,130,140,150,300    power-over-ethernet assigned-class 4    exitsw-flowerroom-6300(config)# sh power-over-ethernet 1/1/10Status and Configuration Information for port 1/1/10  Power Enable           : Yes            PD signature             : single  PoE Port Status        : delivering     PD Type                  : Type2  Alloc-by Configured    : usage          Alloc-by Actual          : lldp-dot3  User Profile Priority  : N/A            Port Config Priority     : Low  Port Priority          : low            Pre-std Detect           : Disabled  PD Requested Class     : Class4         PSE Assigned Class       : Class4  Fault Status           : None           User set Assigned Class  : class4  PD Class Override      : Disabled       Power Pairs Configured   : alt-a-and-alt-b                                          Power Pairs Applied      : alt-a-and-alt-bPoE Counter Information  Over Current Cnt       : 0              MPS Absent Cnt           : 3  Power Denied Cnt       : 0              Short Cnt                : 0Power Information  PSE Voltage            :  54.48 V       PSE Reserved power       :  16.80 W  PD Current Draw        :   0.10 A       PD Power Draw            :   5.45 W  PD Average Power Draw  :   4.88 W       PD Peak Power Draw       :   5.45 WLLDP Information  MED Override             : Disabled  MED Priority             : Critical  PSE TLV Configured       : dot3/med  PSE TLV Sent Type        : dot3  PD TLV Sent Type         : dot3  PSE Allocated Power Value: 15.40 W  PD Requested Power Value : 15.40 W