Restore the default settings on the default profile to clear up the display issue on eth0.
Original Message:
Sent: May 20, 2024 03:31 AM
From: invincible2k
Subject: How to disable AP225 eth1 port ?
Hi schmelzle
Thanks for responding.i have attach command output and default AP Group profile screen shot for reference. Appreciate if you can look into it and suggest.
it is even more confusing on show ap port status ap-name AP-655-01 output. Command output showing Port 0 is disable which is connected with POE switch and working and Port 1 is enable which I forcefully disable.
(Aruba-7210-01) [mynode] #show ap port status ap-name AP-655-01
AP "AP-655-01" Port Status (updated every 60 seconds)
-------------------------------------------------------------
Port MAC Type Forward Mode Admin Oper Speed Duplex 802.3az 802.3bz PoE STP Portfast TX-Packets TX-Bytes RX-Packets RX-Bytes
---- --- ---- ------------ ----- ---- ----- ------ ------- ------- --- --- -------- ---------- -------- ---------- --------
0 74:9e:75:cb:bf:93 5G N/A disabled up 5 Gb/s full disabled Yes N/A N/A N/A 714671 465117738 1020000 391034023
1 74:9e:75:cb:bf:94 5G none enabled down N/A N/A N/A N/A N/A N/A N/A 0 0 0 0
2 76:9e:75:cb:bf:94 USB none disabled down N/A N/A N/A N/A N/A N/A N/A 0 0 0 0
(Aruba-7210-01) [mynode] #show ap wired-port-profile
AP wired port profile List
--------------------------
Name References Profile Status
---- --------- --------------
default 5
NoAuthWiredPort 4 Predefined (changed)
shutdown 9 Predefined
Total:4
(Aruba-7210-01) [mynode] #show ap wired-port-profile default
AP wired port profile "default"
-------------------------------
Parameter Value
--------- -----
Wired AP profile default
Ethernet interface link profile default
AP LLDP profile default
Shut down Yes
Remote-AP Backup Enabled
AAA Profile N/A
Bridge Role logon
Time to wait for authentication to succeed 20 sec
Spanning Tree Disabled
Portfast Disabled
Portfast on trunk Disabled
Loop Protect Enable Disabled
Loop Detection Interval 2
Storm Control Broadcast Disabled
Storm Control Broadcast Threshold 2000
Auto Recovery Enable Disabled
Auto Recovery Interval 300
(Aruba-7210-01) [mynode] #show ap-group TEST
AP group "TEST"
-------------------
Parameter Value
--------- -----
Virtual AP TEST
802.11a radio profile default
802.11a secondary radio profile N/A
802.11g radio profile default
802.11 6GHz radio profile default
802.11 60GHz radio profile default
Ethernet interface 0 port configuration default
Ethernet interface 1 port configuration default
Ethernet interface 2 port configuration shutdown
Ethernet interface 3 port configuration shutdown
Ethernet interface 4 port configuration shutdown
Ethernet usb port configuration shutdown
AP system profile TEST_apsys_ui
AP multizone profile default
802.11a Traffic Management profile N/A
802.11g Traffic Management profile N/A
Regulatory Domain profile default
RF Optimization profile default
RF Event Thresholds profile default
IDS profile default
Mesh Radio profile default
Mesh Cluster profile N/A
WiFi uplink profile N/A
Provisioning profile N/A
AP authorization profile N/A
USB profile default
IoT radio profile N/A
ZigBee Service Profile N/A
Mesh Accesslist profile default
Airslice profile default
GPS service profile default
Original Message:
Sent: May 17, 2024 09:42 AM
From: schmelzle
Subject: How to disable AP225 eth1 port ?
Hi Saud,
Does the output of show ap port status ap-name <name>
for the AP reflect the same? I would double check the port profile is applied correctly by checking the output of show ap wired-port-profile <prof>
and show ap-group <group>
on the 7210.
Original Message:
Sent: May 17, 2024 03:49 AM
From: invincible2k
Subject: How to disable AP225 eth1 port ?
I have Aruba Controller 7210 on software version ArubaOS (MODEL: Aruba7210), Version 8.10.0.9 LSR.
For Security reasons customer wants to disable Aruba AP 655 LAN port 2.
I configured new AP profile Eth1shutdown and select it in AP group profile. In order to verify when I run command show ap power-mgmt-statistics ap-name AP655 i can see Eth status is enables. Need recommendation why Eth 1 port status showing Enabled and how to forcefully disable LAN port 2 of Aruba AP 655.
.
Original Message:
Sent: Jul 09, 2018 09:11 AM
From: cjoseph
Subject: How to disable AP225 eth1 port ?
It will not disable the port for AP redundancy