Thanks Parnassus, details below. I've removed all of the other trunks from the core switch and left just the 1 trunk / uplink to the LAN switch.
192.168.10.20 is the EDGE Firewall/Router
192.168.10.199 is the CORESW Service LAN
10.10.100.1 is the CORESW MGMT LAN
10.10.10.11 is the LAN Switch - Windows DHCP is setup to provide IP addresses with Router option.
CORESWJ8697A
hostname "CORESW"
fault-finder broadcast-storm sensitivity high
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-hdx sensitivity high
fault-finder duplex-mismatch-fdx sensitivity high
fault-finder link-flap sensitivity high
trunk D4-D7 trk13 lacp
ip route 0.0.0.0 0.0.0.0 192.168.10.20
ip routing
snmp-server community "public" unrestricted
router rip
redistribute connected
enable
exit
vlan 1
name "DEFAULT_VLAN"
no untagged C1-C18,C23-C24,D1-D3,D24,E6-E8,F1-F3,Trk1-Trk17,Trk19-Trk23
untagged E5,F4-F6
no ip address
exit
vlan 100
name "VLAN100"
untagged Trk2-Trk15,Trk17,Trk20
tagged Trk1,Trk16,Trk19
ip address 10.10.100.1 255.255.255.0
ip rip 10.10.100.1
exit
vlan 199
name "VLAN199"
untagged C2,C4,C7-C18,E6-E8
ip address 192.168.10.199 255.255.255.0
ip helper-address 192.168.10.5
exit
spanning-tree
spanning-tree Trk13 priority 4
no spanning-tree bpdu-throttle
no tftp server
no autorun
no dhcp config-file-update
no dhcp image-file-update
device-profile name "default-ap-profile"
cos 0
exit
LANSWmodule 1 type j9728a
trunk 45-48 trk13 lacp
ip default-gateway 10.10.100.1
ip timep dhcp
ip route 0.0.0.0 0.0.0.0 10.10.100.1
ip routing
snmp-server community "public" unrestricted
oobm
ip address dhcp-bootp
exit
router rip
redistribute connected
enable
exit
vlan 1
name "DEFAULT_VLAN"
no untagged 1-44,Trk13
ip address dhcp-bootp
exit
vlan 11
name "LAN 1F VLAN 11"
untagged 1-44
ip address 10.10.11.1 255.255.255.0
ip helper-address 192.168.10.5
exit
vlan 100
name "MGMTLAN"
untagged Trk13
ip address 10.10.100.11 255.255.255.0
ip rip 10.10.100.11
exit
spanning-tree
spanning-tree Trk13 priority 4
no tftp server
no autorun
no dhcp config-file-update
no dhcp image-file-update
no dhcp tr69-acs-url
device-profile name "default-ap-profile"
cos 0
exit
activate software-update disable
password operator
Original Message:
Sent: Sep 21, 2022 05:35 PM
From: Davide Poletto
Subject: HP Trunk LACP Port Status - Disabled
Hi! could you show us the current running configuration (regarding the physical member ports of the links aggregation and the logical Port Trunk representing the links aggregation with the issue) and th e output of show lacp, show trunks and show lldp info-remote CLI commands (with just the exact physical/logical ports involved)? GUI could be confusing sometime...CLI will never be.
Original Message:
Sent: 9/21/2022 12:38:00 PM
From: fakiee
Subject: HP Trunk LACP Port Status - Disabled
Hi,
I have trunks setup for my switch uplinks from the core. They are groups of 4 ports set as trunk with LACP on both sides, eg:
trunk 1-4 trk 1 LACP
These uplinks have worked fine with no issues, however I noticed on the old interface that the status is shown as "Disabled" rather than "Active" or "Passive".
Have these been misconfigured, am I missing full LACP capability with the current setup and should I change this to be active or passive?
Thanks!