Wired Intelligent Edge

Hi,

I have trunks setup for my switch uplinks from the core.  They are groups of 4 ports set as trunk with LACP on both sides, eg:

trunk 1-4 trk 1 LACP

These uplinks have worked fine with no issues, however I noticed on the old interface that the status is shown as "Disabled" rather than "Active" or "Passive".

Have these been misconfigured, am I missing full LACP capability with the current setup and should I change this to be active or passive?

Thanks!

Original Message:
Sent: 9/21/2022 12:38:00 PM
From: fakiee
Subject: HP Trunk LACP Port Status - Disabled

Hi,

I have trunks setup for my switch uplinks from the core.  They are groups of 4 ports set as trunk with LACP on both sides, eg:

trunk 1-4 trk 1 LACP

These uplinks have worked fine with no issues, however I noticed on the old interface that the status is shown as "Disabled" rather than "Active" or "Passive".

Have these been misconfigured, am I missing full LACP capability with the current setup and should I change this to be active or passive?

Thanks!

Thanks Parnassus, details below.  I've removed all of the other trunks from the core switch and left just the 1 trunk / uplink to the LAN switch. 

192.168.10.20 is the EDGE Firewall/Router
192.168.10.199 is the CORESW Service LAN
10.10.100.1 is the CORESW MGMT LAN

10.10.10.11 is the LAN Switch - Windows DHCP is setup to provide IP addresses with Router option.

CORESW

J8697A
hostname "CORESW"

fault-finder broadcast-storm sensitivity high
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-hdx sensitivity high
fault-finder duplex-mismatch-fdx sensitivity high
fault-finder link-flap sensitivity high

trunk D4-D7 trk13 lacp

ip route 0.0.0.0 0.0.0.0 192.168.10.20
ip routing
snmp-server community "public" unrestricted
router rip
redistribute connected
enable
exit
vlan 1
name "DEFAULT_VLAN"
no untagged C1-C18,C23-C24,D1-D3,D24,E6-E8,F1-F3,Trk1-Trk17,Trk19-Trk23
untagged E5,F4-F6
no ip address
exit
vlan 100
name "VLAN100"
untagged Trk2-Trk15,Trk17,Trk20
tagged Trk1,Trk16,Trk19
ip address 10.10.100.1 255.255.255.0
ip rip 10.10.100.1
exit
vlan 199
name "VLAN199"
untagged C2,C4,C7-C18,E6-E8
ip address 192.168.10.199 255.255.255.0
ip helper-address 192.168.10.5
exit

spanning-tree
spanning-tree Trk13 priority 4
no spanning-tree bpdu-throttle
no tftp server
no autorun
no dhcp config-file-update
no dhcp image-file-update
device-profile name "default-ap-profile"
cos 0
exit

LANSW

module 1 type j9728a
trunk 45-48 trk13 lacp
ip default-gateway 10.10.100.1
ip timep dhcp
ip route 0.0.0.0 0.0.0.0 10.10.100.1
ip routing
snmp-server community "public" unrestricted
oobm
ip address dhcp-bootp
exit
router rip
redistribute connected
enable
exit
vlan 1
name "DEFAULT_VLAN"
no untagged 1-44,Trk13
ip address dhcp-bootp
exit
vlan 11
name "LAN 1F VLAN 11"
untagged 1-44
ip address 10.10.11.1 255.255.255.0
ip helper-address 192.168.10.5
exit
vlan 100
name "MGMTLAN"
untagged Trk13
ip address 10.10.100.11 255.255.255.0
ip rip 10.10.100.11
exit
spanning-tree
spanning-tree Trk13 priority 4
no tftp server
no autorun
no dhcp config-file-update
no dhcp image-file-update
no dhcp tr69-acs-url
device-profile name "default-ap-profile"
cos 0
exit
activate software-update disable
password operator
Original Message:
Sent: Sep 21, 2022 05:35 PM
From: Davide Poletto
Subject: HP Trunk LACP Port Status - Disabled

Hi! could you show us the current running configuration (regarding the physical member ports of the links aggregation and the logical Port Trunk representing the links aggregation with the issue) and th e output of show lacp, show trunks and show lldp info-remote CLI commands (with just the exact physical/logical ports involved)? GUI could be confusing sometime...CLI will never be.

Original Message:
Sent: 9/21/2022 12:38:00 PM
From: fakiee
Subject: HP Trunk LACP Port Status - Disabled

Hi,

I have trunks setup for my switch uplinks from the core.  They are groups of 4 ports set as trunk with LACP on both sides, eg:

trunk 1-4 trk 1 LACP

These uplinks have worked fine with no issues, however I noticed on the old interface that the status is shown as "Disabled" rather than "Active" or "Passive".

Have these been misconfigured, am I missing full LACP capability with the current setup and should I change this to be active or passive?

Thanks!

Hi, I see but what is the output of:

show lacp
show trunks
show lldp info-remote

CLI commands on both the switches?

Basically here we are first interested about the trk13 Port Trunk status on CORESW switch and about the trk13 Port Trunk status on LANSW switch.

Also the status of physical ports D4-D7 on CORESW switch and 45-48 on LANSW switch is important.
Original Message:
Sent: Sep 22, 2022 08:04 AM
From: chuck foo
Subject: HP Trunk LACP Port Status - Disabled

Thanks Parnassus, details below.  I've removed all of the other trunks from the core switch and left just the 1 trunk / uplink to the LAN switch.

192.168.10.20 is the EDGE Firewall/Router
192.168.10.199 is the CORESW Service LAN
10.10.100.1 is the CORESW MGMT LAN

10.10.10.11 is the LAN Switch - Windows DHCP is setup to provide IP addresses with Router option.

CORESW

J8697A
hostname "CORESW"

fault-finder broadcast-storm sensitivity high
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-hdx sensitivity high
fault-finder duplex-mismatch-fdx sensitivity high
fault-finder link-flap sensitivity high

trunk D4-D7 trk13 lacp

ip route 0.0.0.0 0.0.0.0 192.168.10.20
ip routing
snmp-server community "public" unrestricted
router rip
redistribute connected
enable
exit
vlan 1
name "DEFAULT_VLAN"
no untagged C1-C18,C23-C24,D1-D3,D24,E6-E8,F1-F3,Trk1-Trk17,Trk19-Trk23
untagged E5,F4-F6
no ip address
exit
vlan 100
name "VLAN100"
untagged Trk2-Trk15,Trk17,Trk20
tagged Trk1,Trk16,Trk19
ip address 10.10.100.1 255.255.255.0
ip rip 10.10.100.1
exit
vlan 199
name "VLAN199"
untagged C2,C4,C7-C18,E6-E8
ip address 192.168.10.199 255.255.255.0
ip helper-address 192.168.10.5
exit

spanning-tree
spanning-tree Trk13 priority 4
no spanning-tree bpdu-throttle
no tftp server
no autorun
no dhcp config-file-update
no dhcp image-file-update
device-profile name "default-ap-profile"
cos 0
exit

LANSW

module 1 type j9728a
trunk 45-48 trk13 lacp
ip default-gateway 10.10.100.1
ip timep dhcp
ip route 0.0.0.0 0.0.0.0 10.10.100.1
ip routing
snmp-server community "public" unrestricted
oobm
ip address dhcp-bootp
exit
router rip
redistribute connected
enable
exit
vlan 1
name "DEFAULT_VLAN"
no untagged 1-44,Trk13
ip address dhcp-bootp
exit
vlan 11
name "LAN 1F VLAN 11"
untagged 1-44
ip address 10.10.11.1 255.255.255.0
ip helper-address 192.168.10.5
exit
vlan 100
name "MGMTLAN"
untagged Trk13
ip address 10.10.100.11 255.255.255.0
ip rip 10.10.100.11
exit
spanning-tree
spanning-tree Trk13 priority 4
no tftp server
no autorun
no dhcp config-file-update
no dhcp image-file-update
no dhcp tr69-acs-url
device-profile name "default-ap-profile"
cos 0
exit
activate software-update disable
password operator
Original Message:
Sent: Sep 21, 2022 05:35 PM
From: Davide Poletto
Subject: HP Trunk LACP Port Status - Disabled

Hi! could you show us the current running configuration (regarding the physical member ports of the links aggregation and the logical Port Trunk representing the links aggregation with the issue) and th e output of show lacp, show trunks and show lldp info-remote CLI commands (with just the exact physical/logical ports involved)? GUI could be confusing sometime...CLI will never be.

Original Message:
Sent: 9/21/2022 12:38:00 PM
From: fakiee
Subject: HP Trunk LACP Port Status - Disabled

Hi,

I have trunks setup for my switch uplinks from the core.  They are groups of 4 ports set as trunk with LACP on both sides, eg:

trunk 1-4 trk 1 LACP

These uplinks have worked fine with no issues, however I noticed on the old interface that the status is shown as "Disabled" rather than "Active" or "Passive".

Have these been misconfigured, am I missing full LACP capability with the current setup and should I change this to be active or passive?

Thanks!

I've changed the switch names manually in the text so there may be a few typos on the naming.

LAN switch uses ports 45-48 for physical cables, and switch uses ports D4-D7 - all cables connected

LANSW01

LANSW01# show lacp

LACP

LACP Trunk Port LACP Admin Oper
Port Enabled Group Status Partner Status Key Key
----- ------- ------- ------- ------- ------- ------ ------
45 Active Trk13 Up Yes Success 0 222
46 Active Trk13 Up Yes Success 0 222
47 Active Trk13 Up Yes Success 0 222
48 Active Trk13 Up Yes Success 0 222

LANW01# show trunks

Load Balancing Method: L3-based (default)

Port | Name Type | Group Type
------ + -------------------------------- ---------- + ----- --------
45 | 100/1000T | Trk13 LACP
46 | 100/1000T | Trk13 LACP
47 | 100/1000T | Trk13 LACP
48 | 100/1000T | Trk13 LACP

LANSW01# show lldp info remote-device

LLDP Remote Devices Information

LocalPort | ChassisId PortId PortDescr SysName
--------- + ------------------ ------------------ --------- ------------------
9 | 00 d8 61 68 6a 11 00 d8 61 68 6a 11
17 | 6c 4b 90 af 0c f5 6c 4b 90 af 0c f5
25 | 00 d8 61 45 4c 3d 00 d8 61 45 4c 3d
32 | 00 d8 61 5e dc 46 00 d8 61 5e dc 46
45 | 6c 3b e5 64 84 00 76 D4 CORESW
46 | 6c 3b e5 64 84 00 79 D7 CORESW
47 | 6c 3b e5 64 84 00 78 D6 CORESW
48 | 6c 3b e5 64 84 00 77 D5 CORESW


CORESW

show lacp

D4 Active Trk13 Up Yes Success 0 302
D5 Active Trk13 Up Yes Success 0 302
D6 Active Trk13 Up Yes Success 0 302
D7 Active Trk13 Up Yes Success 0 302

show trunks

D4 | 100/1000T | Trk13 LACP
D5 | 100/1000T | Trk13 LACP
D6 | 100/1000T | Trk13 LACP
D7 | 100/1000T | Trk13 LACP

show lldp info rmote-device

D4 | 38 63 bb 63 6b c0 45 45 LANSW01
D5 | 38 63 bb 63 6b c0 48 48 LANWS01
D6 | 38 63 bb 63 6b c0 47 47 LANSW01
D7 | 38 63 bb 63 6b c0 46 46 LANSW01

Original Message:
Sent: Sep 22, 2022 03:40 PM
From: Davide Poletto
Subject: HP Trunk LACP Port Status - Disabled

Hi, I see but what is the output of:

show lacp
show trunks
show lldp info-remote

CLI commands on both the switches?

Basically here we are first interested about the trk13 Port Trunk status on CORESW switch and about the trk13 Port Trunk status on LANSW switch.

Also the status of physical ports D4-D7 on CORESW switch and 45-48 on LANSW switch is important.
Original Message:
Sent: Sep 22, 2022 08:04 AM
From: chuck foo
Subject: HP Trunk LACP Port Status - Disabled

Thanks Parnassus, details below.  I've removed all of the other trunks from the core switch and left just the 1 trunk / uplink to the LAN switch.

192.168.10.20 is the EDGE Firewall/Router
192.168.10.199 is the CORESW Service LAN
10.10.100.1 is the CORESW MGMT LAN

10.10.10.11 is the LAN Switch - Windows DHCP is setup to provide IP addresses with Router option.

CORESW

J8697A
hostname "CORESW"

fault-finder broadcast-storm sensitivity high
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-hdx sensitivity high
fault-finder duplex-mismatch-fdx sensitivity high
fault-finder link-flap sensitivity high

trunk D4-D7 trk13 lacp

ip route 0.0.0.0 0.0.0.0 192.168.10.20
ip routing
snmp-server community "public" unrestricted
router rip
redistribute connected
enable
exit
vlan 1
name "DEFAULT_VLAN"
no untagged C1-C18,C23-C24,D1-D3,D24,E6-E8,F1-F3,Trk1-Trk17,Trk19-Trk23
untagged E5,F4-F6
no ip address
exit
vlan 100
name "VLAN100"
untagged Trk2-Trk15,Trk17,Trk20
tagged Trk1,Trk16,Trk19
ip address 10.10.100.1 255.255.255.0
ip rip 10.10.100.1
exit
vlan 199
name "VLAN199"
untagged C2,C4,C7-C18,E6-E8
ip address 192.168.10.199 255.255.255.0
ip helper-address 192.168.10.5
exit

spanning-tree
spanning-tree Trk13 priority 4
no spanning-tree bpdu-throttle
no tftp server
no autorun
no dhcp config-file-update
no dhcp image-file-update
device-profile name "default-ap-profile"
cos 0
exit

LANSW

module 1 type j9728a
trunk 45-48 trk13 lacp
ip default-gateway 10.10.100.1
ip timep dhcp
ip route 0.0.0.0 0.0.0.0 10.10.100.1
ip routing
snmp-server community "public" unrestricted
oobm
ip address dhcp-bootp
exit
router rip
redistribute connected
enable
exit
vlan 1
name "DEFAULT_VLAN"
no untagged 1-44,Trk13
ip address dhcp-bootp
exit
vlan 11
name "LAN 1F VLAN 11"
untagged 1-44
ip address 10.10.11.1 255.255.255.0
ip helper-address 192.168.10.5
exit
vlan 100
name "MGMTLAN"
untagged Trk13
ip address 10.10.100.11 255.255.255.0
ip rip 10.10.100.11
exit
spanning-tree
spanning-tree Trk13 priority 4
no tftp server
no autorun
no dhcp config-file-update
no dhcp image-file-update
no dhcp tr69-acs-url
device-profile name "default-ap-profile"
cos 0
exit
activate software-update disable
password operator
Original Message:
Sent: Sep 21, 2022 05:35 PM
From: Davide Poletto
Subject: HP Trunk LACP Port Status - Disabled

Hi! could you show us the current running configuration (regarding the physical member ports of the links aggregation and the logical Port Trunk representing the links aggregation with the issue) and th e output of show lacp, show trunks and show lldp info-remote CLI commands (with just the exact physical/logical ports involved)? GUI could be confusing sometime...CLI will never be.

Original Message:
Sent: 9/21/2022 12:38:00 PM
From: fakiee
Subject: HP Trunk LACP Port Status - Disabled

Hi,

I have trunks setup for my switch uplinks from the core.  They are groups of 4 ports set as trunk with LACP on both sides, eg:

trunk 1-4 trk 1 LACP

These uplinks have worked fine with no issues, however I noticed on the old interface that the status is shown as "Disabled" rather than "Active" or "Passive".

Have these been misconfigured, am I missing full LACP capability with the current setup and should I change this to be active or passive?

Thanks!