Issue is addressed post enabling
AMON_BSSID_TUNNEL_STATS_MESSAGE on the controller side for the AMON messages. Marking the thread as resolved.
------------------------------
Vishnu Mannil
Aruba ERT
If my post addresses your query, give kudos :)
------------------------------
Original Message:
Sent: Dec 06, 2022 09:10 AM
From: Vishnu Mannil
Subject: MD does not display bandwidth usage in airwave
Hi Leo,
Controller monitor page should show the usage and client details graph when we have APs under it and showing the data. This could be either the graphs in not updating or processing data. Could you email me the details on mannil@hpe.com
------------------------------
Vishnu Mannil
Aruba ERT
If my post addresses your query, give kudos :)
Original Message:
Sent: Dec 06, 2022 09:03 AM
From: zhipeng ma
Subject: MD does not display bandwidth usage in airwave
hi dear
This is my lab environment, but MD cannot see usage in many scenarios. The total bandwidth can be seen, and the traffic of the client can be seen, including the traffic of each ssid; is this designed in this way?
------------------------------
leo ma
Original Message:
Sent: Dec 06, 2022 08:46 AM
From: Vishnu Mannil
Subject: MD does not display bandwidth usage in airwave
Hi Leo,
Request you to open a TAC case. There are chances that we may not be receiving date or server not processing it. We will need to check this from server point.
------------------------------
Vishnu Mannil
Aruba ERT
If my post addresses your query, give kudos :)
Original Message:
Sent: Dec 06, 2022 07:45 AM
From: zhipeng ma
Subject: MD does not display bandwidth usage in airwave
"default-amp" has pointed to the airwave ip address,
------------------------------
leo ma
Original Message:
Sent: Dec 05, 2022 11:17 AM
From: Vishnu Mannil
Subject: MD does not display bandwidth usage in airwave
Please make sure on the controller we have the Amon profile "default-amp" pointed to the Airwave IP address.
------------------------------
Vishnu Mannil
Aruba ERT
If my post addresses your query, give kudos :)
Original Message:
Sent: Dec 05, 2022 08:51 AM
From: zhipeng ma
Subject: MD does not display bandwidth usage in airwave
hi
Both AP and ac are in the same group, and amon vs snmp is yes, but the usage cannot be seen in the controller
------------------------------
leo ma
Original Message:
Sent: Dec 01, 2022 11:18 AM
From: Vishnu Mannil
Subject: MD does not display bandwidth usage in airwave
Pavan is referring to the group on Airwave.
On other note are the APs showing any usage or client on Airwave side? Are we having "Prefer Amon Vs SNMP" set to yes under Amp setup --> General --> Additional AMP Services
Make sure, the amon profile on Controller(default amp) is mapped to Airwave IP address
------------------------------
Vishnu Mannil
Aruba ERT
If my post addresses your query, give kudos :)
Original Message:
Sent: Nov 30, 2022 07:30 PM
From: zhipeng ma
Subject: MD does not display bandwidth usage in airwave
Does this refer to the group of the AP on the MD, or the group on the airwave?
------------------------------
leo ma
Original Message:
Sent: Nov 30, 2022 01:02 PM
From: Pavan Arshewar
Subject: MD does not display bandwidth usage in airwave
If APs are placed in different group then we don't show usage for controller.
------------------------------
Pavan Arshewar
Principal Network Engineer
If my post addresses your query, give kudos!
Original Message:
Sent: Nov 30, 2022 08:27 AM
From: zhipeng ma
Subject: MD does not display bandwidth usage in airwave
hi
The MD is online normally, and the status is normal, but the bandwidth usage cannot be seen. Why?
------------------------------
leo ma
------------------------------