Hi Matthew,
Thank you for replying.. I created it again under Wired Intelligent Edge Community.
Here again...
Hello everyone,
I'm new in Aruba (come from Cisco).. and I need some help please.
Scenario:
Fortigate on one side, Aruba 3810M (WC.16.10) on the other.
I'd like to configure a transport VLAN between them and enable OSPF.
Only the 3810 is under my administration.
So in Cisco world, I'd go this way...
router ospf 1
router-id 10.28.15.243
area 1 authentication message-digest
redistribute connected subnets
redistribute static metric 1000 metric-type 1 subnets
passive-interface default
no passive-interface Vlan700
network 10.28.8.0 0.0.7.255 area 1
interface vlan 700
description L3-VLAN-700
ip address 10.28.15.130 255.255.255.248
ip ospf message-digest-key 1 md5 0 [key]
ip ospf network point-to-point
ip ospf cost 10
no shutdown
interface GigabitEthernet1/0/1
description wan-01
switchport access vlan 700
switchport mode access
I'm working in a document here, not the switch itself. The 3810 is in production, so I'm planning on having everything prepared and then just paste the config during migration day.
I'm struggling with the configuration in the 3810.. this is what I'd like to do.
OSPF configuration for the 3810:
ip routing enable
!
router ospf 0
area backbone
enable
redistribute connected
exit
!
!
ip router id [ip address lo0]
!
!
vlan 700
tagged 1/1
name L3-VLAN-700
ip address 172.20.30.1 255.255.255.252 à Fortigate .2
ip ospf area 0
!
!
interface 1/1
name [name]
tagged vlan 700
!
!
I don't know if the above config is correct/complete.. also, I don't know if I have to add the OSPF statements in all my SVIs, like this...
vlan 110
tagged 1/1
name SRV-VLAN
ip address 172.20.3.1 255.255.255.0
ip ospf 172.20.3.1 area 0
!
!
vlan 200
tagged 1/1
name CORP-VLAN
ip address 172.20.30.1 255.255.248.0
ip helper-address 172.20.3.175
ip helper-address 172.20.3.205
ip ospf area 0
Would the above be the equivalent to the "network" statement in the OSPF config for Cisco?
I'd really appreciate any input!
!!Parnassus, if you read this.. please help me, I've read many of your answers since I moved to HP, you are a genius man!!
Thank you in advance!
Original Message:
Sent: Jul 06, 2022 07:18 AM
From: Matthew Sutherland
Subject: New post
Hi Damian,
What switch would you be using for OSPF?
Original Message:
Sent: Jul 04, 2022 07:27 AM
From: Damian Ostiz
Subject: New post
Hi,
I've created a new post/discussion on Friday and since I'm new here, I received the ""First time post alert: If this is your first post, please allow up to 24 hours for your post to appear. Thank you for your contribution.""
Problem is, I'm still waiting to see it, not even want to talk about someone answering me.. Is there something else I have to do for my post to be shown?
It was about OSPF and the differences between Aruba and Cisco, when it comes to configuration.
Needless to say.. I'm new around here, and also in the HP networking world.
Is there any support site for Airheads community?
Cheers,
Damian