Larry,
I have an old 3750 running IOS 15.0(2)SE1 and was able to get the port channel up using the following:
Switch#show run | begin interface
interface Port-channel1
switchport mode access
!
interface GigabitEthernet1/0/1
switchport mode access
power inline never
channel-group 1 mode active
!
interface GigabitEthernet1/0/2
switchport mode access
power inline never
channel-group 1 mode active
Disregard that PoE is disabled. My 3750 only support Pre-Standard and 802.3af and to have the second eth1 up on the IAP-225, you need 802.3at or at least 51v on the PoE rail which this one does not so I'm using an external supply for my IAP-225. You need to set the mode to Active because that instructs the switch to send LACP PDUs.
Here are the relevent Cisco outputs once LACP was up:
Switch#show lacp 1 counters
LACPDUs Marker Marker Response LACPDUs
Port Sent Recv Sent Recv Sent Recv Pkts Err
---------------------------------------------------------------------
Channel group: 1
Gi1/0/1 68 16 0 0 0 0 0
Gi1/0/2 64 14 0 0 0 0 0
Switch#show lacp 1 neighbor
Flags: S - Device is requesting Slow LACPDUs
F - Device is requesting Fast LACPDUs
A - Device is in Active mode P - Device is in Passive mode
Channel group 1 neighbors
Partner's information:
LACP port Admin Oper Port Port
Port Flags Priority Dev ID Age key Key Number State
Gi1/0/1 SA 255 1864.72c5.843a 28s 0x0 0x11 0x1 0x3D
Gi1/0/2 SA 255 1864.72c5.843a 28s 0x0 0x11 0x2 0x3D
Switch#show lacp 1 internal
Flags: S - Device is requesting Slow LACPDUs
F - Device is requesting Fast LACPDUs
A - Device is in Active mode P - Device is in Passive mode
Channel group 1
LACP port Admin Oper Port Port
Port Flags State Priority Key Key Number State
Gi1/0/1 SA bndl 32768 0x1 0x1 0x102 0x3D
Gi1/0/2 SA bndl 32768 0x1 0x1 0x103 0x3D
Here is the bootup sequence from my IAP. I am running 6.3.1.4-4.0.0.5. Notice at the 22/23 second mark, the interface is being configured for 802.3ad which is LACP.
[ 0.000000]
[ 0.000000] Aruba Networks
[ 0.000000] ArubaOS Version 6.3.1.4-4.0.0.5 (build 43022 / label #43022)
[ 0.000000] Built by p4build@stan on 2014-04-03 at 13:50:44 PDT (gcc version 4.5.1)
[ 0.000000]
[ 0.000000] Memory: 508988k/524288k available (9744k kernel code, 15300k reserved, 504k data, 355k bss, 6380k init)
[ 0.002949] Processor 1 found.
[ 0.123952] Brought up 2 CPUs
[ 0.200475] PCI: Probing PCI hardware
[ 0.243530] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.306536] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.368744] pci 0000:00:00.0: enabling device (0106 -> 0107)
[ 0.435941] pci 0001:02:00.0: enabling device (0106 -> 0107)
[ 5.006300] ee000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank
[ 5.081344] Amd/Fujitsu Extended Query Table at 0x0040
[ 5.142863] number of CFI chips: 1
[ 5.188059] /proc/gfar_eth0_stats created
[ 5.238783] /proc/gfar_eth1_stats created
[ 5.302922] wdg_create_new_proc_entry: proc initializedEnabling watchdog on CPU 1
[ 5.363393] Enabling watchdog on CPU 0
[ 5.444182]
[ 5.444186] Starting Kernel SHA1 KAT ...Starting Kernel HMAC SHA1 FIPS KAT ...Completed Kernel HMAC SHA1 FIPS KAT
[ 5.452389] Starting Kernel HMAC SHA256 FIPS KAT ...Completed Kernel HMAC SHA256 FIPS KAT
[ 5.453137] Starting Kernel HMAC SHA384 FIPS KAT ...Completed Kernel HMAC SHA384 FIPS KAT
[ 5.453638] Starting Kernel HMAC SHA512 FIPS KAT ...Completed Kernel HMAC SHA512 FIPS KAT
[ 5.454194] Starting Kernel AES-CBC FIPS KAT ...Completed Kernel AES-CBC FIPS KAT
[ 5.459264] Starting Kernel AES-CCM FIPS KAT ...Completed Kernel AES-CCM FIPS KAT
[ 5.459702] Starting Kernel 3DES-CBC FIPS KAT ...Completed Kernel 3DES-CBC FIPS KAT
[ 6.156822] Completed Kernel SHA1 KAT
[ 6.201643] Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
[ 6.289910] Starting Kernel DES KAT ...Completed Kernel DES KAT
[ 6.361859] Starting Kernel AES KAT ...Completed Kernel AES KAT
[ 6.405658]
Domain Name: arubanetworks.com
No panic info available
Check backup ENV.
[ 9.726448] p1020_soc: P1020 Misc Utils Driver version 1
Ethernet port 1 mode: active-standby
[ 9.984975] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.053719] ADDRCONF(NETDEV_UP): bond0: link is not ready
[ 10.139552] bonding: bond0: enslaving eth0 as a backup interface with a down link.
[ 10.246082] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 10.331463] bonding: bond0: enslaving eth1 as a backup interface with a down link.
Using primary ap config
wifi uplink not present...
extended ssid config detected...
do ethtool autoneg on for eth0
[ 13.388241] PHY: eth0 (mdio@ffe24000:00) - Link is Up - 1000/Full
[ 13.711016] bonding: bond0: link status definitely up for interface eth0.
[ 13.769629] PHY: eth1 (mdio@ffe24000:01) - Link is Up - 1000/Full
[ 13.865235] bonding: bond0: making interface eth0 the new active one.
[ 13.942383] bonding: bond0: first active interface up!
[ 14.004014] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
[ 14.403015] bonding: bond0: link status definitely up for interface eth1.
Mesh is DISABLED on this device.
[ 16.412516] AP xml model 66, num_radios 2 (jiffies 7999)
[ 16.476113] init_asap_mod: installation:0
[ 16.524071] radio 0: band 1 ant 0 max_ssid 16
[ 16.576182] radio 1: band 0 ant 0 max_ssid 16
[ 16.628299] election init: rand=11 HZ=500
[ 16.676239] IAP client match init
[ 16.715895] ethernet_device_event: dev eth0 is up
[ 16.772189] ethernet_device_event: dev eth1 is up
[ 16.836991] ASAP Slowpath initialized
notify asap_mod 3g no present...
Starting watchdog process...
Getting an IP ad[ 16.999965] bonding: bond0: eth0 is already the current active slave.
dress...
Dec 31 16:00:16 udhcpc[2052]: udhcpc (v0.9.9-pre) started
Dec 31 16:00:16 udhcpc[2052]: send_discover: pkt num 0, secs 0
Dec 31 16:00:16 udhcpc[2052]: Sending discover...
Dec 31 16:00:18 udhcpc[2052]: send_discover: pkt num 1, secs 2
Dec 31 16:00:18 udhcpc[2052]: Sending discover...
Dec 31 16:00:20 udhcpc[2052]: send_discover: pkt num 2, secs 4
Dec 31 16:00:20 udhcpc[2052]: Sending discover...
[ 22.392621] bonding: bond0: Warning: the permanent HWaddr of eth0 - 18:64:72:c5:84:3a - is still in use by bond0. Set the HWaddr of eth0 to a different address to avoid conflicts.
[ 22.584322] bonding: bond0: releasing active interface eth0
[ 22.651064] bonding: bond0: making interface eth1 the new active one.
[ 22.737175] ethernet_device_event: dev eth0 is down
[ 22.798566] bonding: bond0: releasing active interface eth1
[ 22.875132] ethernet_device_event: dev eth1 is down
[ 22.945569] bonding: bond0: setting xmit hash policy to layer2+3 (2).
[ 23.025047] bonding: bond0: setting mode to 802.3ad (4).
[ 23.091034] ADDRCONF(NETDEV_UP): bond0: link is not ready
[ 23.161806] ethernet_device_event: dev eth0 is up
[ 23.218155] bonding: bond0: enslaving eth0 as a backup interface with an up link.
[ 23.308019] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
Dec 31 16:00:22 [ 23.393065] ethernet_device_event: dev eth1 is up
udhcpc[2052]: No[ 23.459771] bonding: bond0: enslaving eth1 as a backup interface with an up link.
lease, forking to background.
[ 26.642407] PHY: eth0 (mdio@ffe24000:00) - Link is Up - 1000/Full
[ 26.862292] PHY: eth1 (mdio@ffe24000:01) - Link is Up - 1000/Full
Dec 31 16:00:42 udhcpc[2202]: send_discover: pkt num 0, secs 26
Dec 31 16:00:42 udhcpc[2202]: Sending discover...
Dec 31 16:00:44 udhcpc[2202]: send_discover: pkt num 1, secs 28
Dec 31 16:00:44 udhcpc[2202]: Sending discover...
Dec 31 16:00:46 udhcpc[2202]: send_discover: pkt num 2, secs 30
Dec 31 16:00:46 udhcpc[2202]: Sending discover...
Dec 31 16:01:08 udhcpc[2202]: send_discover: pkt num 0, secs 52
Dec 31 16:01:08 udhcpc[2202]: Sending discover...
Dec 31 16:01:08 udhcpc[2202]: send_selecting: pkt num 0, secs 52
Dec 31 16:01:08 udhcpc[2202]: Sending select for 192.168.210.3...
Dec 31 16:01:08 udhcpc[2202]: Lease of 192.168.210.3 obtained, lease time 86400
D[ 68.819005] ip_time_handler: Got ip and packets on bond0 Started master election 3-0, rand 14
ec 31 16:01:08 udhcpc[2202]: DHCP OPT 43 deleted airwave config
192.168.210.3 255.255.255.0 192.168.210.1
Compressing all files in the /etc/httpd directory...
Done.
Starting Webserver
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
NTP Server not saved in flash... using default
[ 72.836531] wifi0: AP type AP-225, radio 0, max_bssids 16
[ 72.933052] Enabling eth1 due to power change [power profile 1]
[ 73.060137] wifi1: AP type AP-225, radio 1, max_bssids 16
Clearing P1020 PCIe Error Status
shutting down watchdog process (nanny will restart it)...
Completed SW FIPS KAT test
<<<<< Welcome to the Access Point >>>>>
And then finally here is the LACP output from the IAP.
18:64:72:c5:84:3a# show lacp status
AP LACP Status
--------------
Link Status LACP Rate Num Ports Actor Key Partner Key Partner MAC
----------- --------- --------- --------- ----------- -----------
Up slow 2 17 1 00:27:0c:6d:d8:80
Slave Interface Status
----------------------
Slave I/f Name Permanent MAC Addr Link Status Member of LAG Link Fail Count
-------------- ------------------ ----------- ------------- ---------------
eth0 18:64:72:c5:84:3a Up Yes 0
eth1 18:64:72:c5:84:3b Up Yes 0
Traffic Sent on Enet Ports
--------------------------
Radio Num Enet 0 Tx Count Enet 1 Tx Count
--------- --------------- ---------------
0 0 0
1 0 0
non-wifi 2 10
I hope this helps to compare against what you are seeing.