Network Management

Reply
Occasional Contributor I

Airwave 8.2.2.1 and setting trasmit power on single IAP

I have IAP205 that I handle from Airwave. When I try to set Channel and Transmit Power on a single IAP on "Access Point" -> "Radio" -> "Adminstrator Assigned" it does not it does not take it, there is no change ??

Why is that ?

(IAP version 4.2.4 )

Aruba Employee

Re: Airwave 8.2.2.1 and setting trasmit power on single IAP

Hi,

 

Are you managing IAPs using template or instant GUI mode? Could share screen shot for better understanding.

 

Regards,

Pavan

Occasional Contributor I

Re: Airwave 8.2.2.1 and setting trasmit power on single IAP

Hi, I´m using AirWave and Groups->Instant config->VC list->VC-> Menu -> Accesspoints See attached screed shot When I do changes here and apply them. It does note change, it does not take it.
Aruba Employee

Re: Airwave 8.2.2.1 and setting trasmit power on single IAP

Hi,

 

Able to push the configuration, after chaning the values, click apply.

ALE.PNG

 

ALE.PNG

 

once we make changes, click Apply button, need to wait for couple of minutes for changes to apply.

 

Regards,

Pavan

Occasional Contributor I

Re: Airwave 8.2.2.1 and setting trasmit power on single IAP

Does not work for me . . .

I did a change of AP-name in General tab, saved it (but not Apply)

went to Radio tab, made the changes you se below, pressed Save (but really any response, pressed Apply . . . and waited 

save and apply bottoms is greyed out

I´ll waited for 10 minutes, nothing happens.

I go to General TAB again and get the messaged you se in attachment.

the change of AP name has been done but not signal stringth .

 

Aruba Employee

Re: Airwave 8.2.2.1 and setting trasmit power on single IAP

Hi,

 

After apply, are you seeing any options which I have highlighted in  below screen shot. If yes, wait for few minutes and also you could try click on VC, it will show the mismatch config which we are tyring to push, down the page we will see Apply ALL button try click that button to apply configuration.

ALE.PNG

Regards,

Pavan

Occasional Contributor I

Re: Airwave 8.2.2.1 and setting trasmit power on single IAP

I see that my change of AP name was stuck as you describe and I could apply it again. But it was only the the name change that was presented as not applied. The changes on channel and signal was not display among pending changes and status and conf is unchanged. And if I only do the radio changes it will not be displayed as pending at all. Here below is my config history on that VC. It does not show any entry on radio parameter changes at all even if i have tried several time now. I probably need to open a support case on this. I have two separat systems but both same release on Airwave and APs. both system behave the same way 2017-06-28 14:27:22,095 INFO Config 4 Config Result Config Status: success Config Push Result: per-ap-settings 40:e3:d6:ce:8d:6c: OK hostname "TestAP_131": OK exit: OK 2017-06-28 14:26:36,980 INFO Config 4 Message sent { "command": "audit_result_update", "ap_id": 4, "audit_status": "Good" } 2017-06-28 14:26:36,980 INFO Config 4 cluster [SiteLab] has been updated, disabling auto-repair 2017-06-28 14:26:18,700 INFO Config 4 sending delta: { "ap_id": "4", "command": "config_update", "delta_config": "\nper-ap-settings 40:e3:d6:ce:8d:6c\n hostname TestAP_131\nexit\n", "hashed_management_password": "0" } 2017-06-28 14:26:12,670 INFO HTTP[1] 4 [] 2017-06-28 14:26:12,669 INFO HTTP[2] 4 Message sent { "ap_id": 4, "command": "request_audit" } 2017-06-28 12:57:49,192 INFO HTTP[1] 4 [] 2017-06-28 04:23:05,518 INFO Config 4 cluster [SiteLab] is not in auto-repair mode, skipping 2017-06-28 04:23:05,518 INFO Config 4 Message sent { "command": "audit_result_update", "ap_id": 4, "audit_status": "Good" } 2017-06-28 04:23:05,418 INFO Config 4 cluster [SiteLab] is not in auto-repair mode, skipping 2017-06-28 04:23:05,418 INFO Config 4 Message sent
Aruba Employee

Re: Airwave 8.2.2.1 and setting trasmit power on single IAP

Hi,

 

Is this new deployment, could you try clear browser cache and check and also try on different browser aswell.

 

If above does not work, try restart IGC service once and check the status.

 

#psk airwave.igc

 

IAP code 4.2.4 supported in 8.2.2.1 version.

 

Regards,

Pavan

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: