Wireless Access

Reply
Regular Contributor I

AP 105's are unable to be provisioned by controller 620

hi guys,
i have do a factory reset of my controller 620.
after this, i tried to configure my AP, but they cannot link them successfully to my controller.

i have two different situation.

On one controller i receive this:

APBoot 1.2.4.4 (build 26618)
Built: 2011-01-07 at 13:42:04

Model: AP-10x
CPU: AR7161 revision: A2
Clock: 680 MHz, DDR clock: 340 MHz, Bus clock: 170 MHz
DRAM: 128 MB
POST1: passed
Copy: done
Flash: 16 MB
PCI: scanning bus 0 ...
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 168c 0029 00002 01 10000000 00000000 00000000 00000000
01 00 168c 0029 00002 01 10010000 00000000 00000000 00000000
Net: eth0
Radio: ar922x#0, ar922x#1

Hit <Enter> to stop autoboot: 0
Checking image @ 0xbf100000

Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
ELF file is 32 bit
Loading .text @ 0x80e00000 (5590776 bytes)
Loading .data @ 0x81354f00 (32 bytes)
Clearing .bss @ 0x81354f20 (16 bytes)
## Starting application at 0x80e00000 ...
Uncompressing.....................................................
ú
Aruba Networks
ArubaOS Version 6.2.0.3 (build 37213 / label #37213)
Built by p4build@corsica.arubanetworks.com on 2013-02-15 at 06:09:03 PST (gcc ve rsion 4.3.3)
CPU Rev: aa
71x CPU
Flash variant: default
Cache parity protection disabled
Using 340.000 MHz high precision timer. cycles_per_jiffy=680000
Memory: 120960k/131072k available (1920k kernel code, 9984k reserved, 755k data, 4688k init, 0k highmem)
available.
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=8388608,origSize=21110272
LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com> ........................... ................................................................................ ................................................................................ ................................................................................ ........................................................
AR7100 GPIOC major 0
wdt: registered with refresh
Enabling Watchdog
Talisker RSSI LED initialization
Creating 1 MTD partitions on "ar7100-nor0":
0x00000000-0x01000000 : "flash"
i2c /dev entries driver
i2c-talisker: using default base 0x18040000
AD7416 driver probing for devices on AR7100 I2C
.<6>lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver

Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
Starting Kernel DES KAT ...Completed Kernel DES KAT
Starting Kernel AES KAT ...Completed Kernel AES KAT

Domain Name: arubanetworks.com
No panic info available
Testing TPM... Passed
ag7100_mod: module license 'unspecified' taints kernel.
AG7100: Length per segment 512
AG7100: Max segments per packet 4
AG7100: Max tx descriptor count 400
AG7100: Max rx descriptor count 252
AG7100: fifo cfg 3 018001ff
AG7100CHH: Mac address for unit 0
AG7100CHH: d8:c7:c8:ce:d7:19
ATHRF1: Port 0, Neg Success
ATHRF1: unit 0 phy addr 0 ATHRF1: reg0 0
AP xml model 39, num_radios 2 (jiffies 5481)
init_asap_mod: installation:0
radio 0: band 1 ant 0 max_ssid 8
radio 1: band 0 ant 0 max_ssid 8
setting bond0 as bridge child
setting gre0 as split child
Starting watchdog process...
Getting an IP address...
ag7100_ring_alloc Allocated 4800 at 0x87b48000
ag7100_ring_alloc Allocated 3024 at 0x86b0a000
AG7100: cfg1 0xf cfg2 0x7014
ATHRF1: Port 0, Neg Success
ATHRF1: unit 0 phy addr 0 ATHRF1: reg0 3100
AG7100: unit 0: phy not up carrier 1
Writing 4
ADDRCONF(NETDEV_UP): bond0: link is not ready
AG7100: unit 0 phy is up...RGMii 100Mbps full duplex
AG7100: pll reg 0x18050010: 0x1099 AG7100: cfg_1: 0x1ff0000
AG7100: cfg_2: 0x3ff
AG7100: cfg_3: 0x18001ff
AG7100: cfg_4: 0xffff
AG7100: cfg_5: 0x7ffef
AG7100: done cfg2 0x7115 ifctl 0x10000 miictrl 0x12
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
DHCP timed out... valid v6 address present. continue
fe80::dac7:c8ff:fece:d719/64 Scope:Link
fe80::dac7:c8ff:fece:d719/64 Scope:Link
Running ADP...cat: /tmp/master: No such file or directory
Done. Master is
killall: nanny: no process killed
killall: sapd: no process killed
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
Restarting system.

 

On the other AP instead:
-------------------------------------------
APBoot 1.2.4.4 (build 26618)
Built: 2011-01-07 at 13:42:04

Model: AP-10x
CPU: AR7161 revision: A2
Clock: 680 MHz, DDR clock: 340 MHz, Bus clock: 170 MHz
DRAM: 128 MB
POST1: passed
Copy: done
Flash: 16 MB
PCI: scanning bus 0 ...
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 168c 0029 00002 01 10000000 00000000 00000000 00000000
01 00 168c 0029 00002 01 10010000 00000000 00000000 00000000
Net: eth0
Radio: ar922x#0, ar922x#1

Hit <Enter> to stop autoboot: 0
Checking image @ 0xbf100000
Invalid image format version: 0xffffffff
Checking image @ 0xbf800000
Invalid image format version: 0xffffffff
eth0 up: 100 Mb/s full duplex
DHCP broadcast 1
DHCP broadcast 2
DHCP broadcast 3
DHCP broadcast 4
DHCP broadcast 5

Retry count exceeded; starting again
eth0 up: 100 Mb/s full duplex
-------------------------------------------

on this ap i have use the command " factory_reset"

my controller have version 6.2.1.1

have any idea?

 

thanks in advance

Andrea
Guru Elite

Re: AP 105's are unable to be provisioned by controller 620

Can you try these three commands on one of them?

purgeenv
Saveenv
Boot

Tim Cappalli | Aruba Security TME
@timcappalli | timcappalli.me | ACMX #367 / ACCX #480
Aruba Employee

Re: AP 105's are unable to be provisioned by controller 620

Both the Aps are not gettign IP address. 

 

ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
DHCP timed out... 

 

 

on second 

 

eth0 up: 100 Mb/s full duplex
DHCP broadcast 1
DHCP broadcast 2
DHCP broadcast 3
DHCP broadcast 4
DHCP broadcast 5

Retry count exceeded; starting again

 

Vinod Kumaar AVM ACMX, ACDX
Principal Network Engineer
Customer Advocacy | Aruba Networks Inc.

Did something you read in the Community solve a problem for you? If so, click "Accept as Solution" in the bottom right hand corner of the post.
Regular Contributor I

Re: AP 105's are unable to be provisioned by controller 620

thank for your answer,

 

well, yes on both AP's

Andrea
Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: