Wireless Access

Reply
Occasional Contributor II

IAP-215 kind of died, can't convert to CAP.

Mobility Controller 7205. Some 30 IAP-215 in CAP-mode. 6.5.4.2 software.

 

I got reports that wifi-connectivity was down in one room, and I remembered that the AP had frozen a while back. This time it responded to ping, but was otherwise unusable and radio was down. I pulled the power, and after that it kept rebooting i a cycle of a few minutes.

 

I replaced the AP, and tried resetting it. The AP is an IAP-model, so I could get into it again. After some fiddling about I realized that I was unable to convert it back to a CAP again as long as it has the same ip-address as before. Even when I deleted (cleared) the AP from the list in the controller.

 

After configuring another IP-address for the AP I managed to get the AP to download a CAP-image from the controller, but now it has been sitting there with a blinking green power and booting for almost 20 minutes. It never shows up in the provisioning-list.

 

Could there be something wrong with the AP, as in hardware-wise? I have converted a lot of AP's back and forth but this one seems strange and unwilling to perform.

 

I got tired of waiting for it to boot, and pulled the plug. Now I'm back in the mode where I started. That is, it responds to a few (six) ping packets and the spontaniously reboots.

Re: IAP-215 kind of died, can't convert to CAP.

It could be a possible hardware fault, have you been able to attach a console cable a record the output? If so could you post it here?


ACMA, ACMP, ACSA
If my post addresses your query, give kudos:)
Occasional Contributor II

Re: IAP-215 kind of died, can't convert to CAP.

I'll have to do that.

Guru Elite

Re: IAP-215 kind of died, can't convert to CAP.

Ip address conflict?  Check to see if you can still ping that ip address when the AP is down...



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Occasional Contributor II

Re: IAP-215 kind of died, can't convert to CAP.

Looks to me there's a crash

 

[ 50.919068] wifi0: AP type AP-215, radio 0, max_bssids 16
[ 51.136303] aruba_usb_power_control:1136 en:1 status:0
[ 51.197903] aruba_enable_usb_block:556 Enabled USB
[ 51.255235] aruba_usb_power_control:1141 Enable USB power control for 214/215
[ 51.340713] tomatin_usb_power_control:975 enable the USB
[ 51.701067] wifi1: AP type AP-215, radio 1, max_bssids 16
[ 51.979995] irq 18: nobody cared (try booting with the "irqpoll" option)
[ 52.060217] Call Trace:
[ 52.089410] [cfff1f40] [c000853c] show_stack+0x44/0x154 (unreliable)
[ 52.165477] [cfff1f80] [c0084aac] __report_bad_irq+0x34/0xbc
[ 52.233204] [cfff1fa0] [c0084d08] note_interrupt+0x1d4/0x230
[ 52.300929] [cfff1fd0] [c0085aac] handle_fasteoi_irq+0xf4/0x13c
[ 52.371787] [cfff1ff0] [c0010654] call_handle_irq+0x18/0x28
[ 52.438472] [cc6798c0] [c0004684] do_IRQ+0xcc/0x18c
[ 52.496823] [cc6798f0] [c0011320] ret_from_except+0x0/0x18
[ 52.562868] --- Exception: 501 at read_radio_reg+0x104/0x1f8 [wl]
[ 52.562871] LR = wlc_phy_switch_radio_acphy+0x112c/0x2748 [wl]
[ 52.709884] [cc6799b0] [c90944c8] mod_radio_reg+0x24/0x50 [wl] (unreliable)
[ 52.793361] [cc6799d0] [c905025c] wlc_phy_switch_radio_acphy+0x112c/0x2748 [wl]
[ 52.881000] [cc679a50] [c90999f0] wlc_phy_switch_radio+0x2b0/0x3f8 [wl]
[ 52.960304] [cc679a80] [c9097084] wlc_phy_init+0x168/0x588 [wl]
[ 53.031285] [cc679ac0] [c919f8e4] wlc_bmac_set_extlna_pwrsave_shmem+0x28c/0xeb4 [wl]
[ 53.124144] [cc679af0] [c919bf7c] wlc_bmac_init+0xdd4/0x20e8 [wl]
[ 53.197215] [cc679b80] [c91bf088] wlc_init+0x130/0xfb8 [wl]
[ 53.264032] [cc679c00] [c91b9330] wl_init+0x34/0x60 [wl]
[ 53.327728] [cc679c10] [c91cc314] wlc_up+0x1d0/0x694 [wl]
[ 53.392462] [cc679c40] [c91b948c] wl_up+0x58/0xbc [wl]
[ 53.454082] [cc679c60] [c92a1f9c] aruba_wl_init_up+0x28/0x1f8 [wl]
[ 53.528197] [cc679c80] [c92a2390] aruba_wl_init+0x224/0x714 [wl]
[ 53.600223] [cc679ce0] [c91bcc20] wl_ams_forward_capture+0xc64/0x197c [wl]
[ 53.682673] [cc679dc0] [c92f4b44] wl_pci_probe+0x134/0x27c [wl]
[ 53.753530] [cc679dd0] [c0166f98] pci_device_probe+0x80/0xa4
[ 53.821259] [cc679df0] [c018ce54] driver_probe_device+0xa4/0x1d4
[ 53.893151] [cc679e10] [c018d040] __driver_attach+0xbc/0xc0
[ 53.959839] [cc679e30] [c018bd58] bus_for_each_dev+0x60/0x9c
[ 54.027569] [cc679e60] [c018cac0] driver_attach+0x24/0x34
[ 54.092168] [cc679e70] [c018c620] bus_add_driver+0xb0/0x268
[ 54.158857] [cc679ea0] [c018d2f4] driver_register+0x88/0x154
[ 54.226588] [cc679ec0] [c0167258] __pci_register_driver+0x54/0xe4
[ 54.299650] [cc679ee0] [c96402b4] init_module+0x2b4/0x318 [wl]
[ 54.369462] [cc679ef0] [c0001ec4] do_one_initcall+0x3c/0x1d0
[ 54.437197] [cc679f20] [c007fabc] sys_init_module+0xdc/0x1e0
[ 54.504922] [cc679f40] [c0010cc8] ret_from_syscall+0x0/0x3c
[ 54.571609] --- Exception: c01 at 0x4831cb90
[ 54.571613] LR = 0x10027830
[ 54.660168] handlers:
[ 54.687262] [<c001ed38>] (fsl_ifc_ctrl_irq+0x0/0x1e4)
[ 54.747714] Disabling IRQ #18

[ 88.046858] BUG: soft lockup - CPU#0 stuck for 31s! [busybox:2122]
[ 88.120826] Modules linked in: wl(+) asap_mod drvlog_mod(P)
[ 88.187529] **bleep**: c9094cf0 LR: c9054d20 CTR: c9054cb4
[ 88.246915] REGS: cc679980 TRAP: 0901 Tainted: P (2.6.35)
[ 88.326092] MSR: 00029000 <EE,ME,CE> CR: 22004044 XER: 20000000
[ 88.399058] TASK = ce0a1300[2122] 'busybox' THREAD: cc678000 CPU: 0 STACK FREE: 5088
[ 88.489721] GPR00: 0000001f cc679a30 ce0a1300 c97c8000 000001b0 00008000 00008000 00000001
[ 88.589786] GPR08: 00001c70 0000002a 00000000 d10303fe 28004042
[ 88.664063] **bleep** [c9094cf0] phy_reg_mod+0xac/0x16c [wl]
[ 88.725656] LR [c9054d20] wlc_phy_resetcca_acphy+0x288/0x600 [wl]
[ 88.798581] Call Trace:
[ 88.827762] [cc679a30] [caea0000] 0xcaea0000 (unreliable)
[ 88.892489] [cc679a60] [c9054d20] wlc_phy_resetcca_acphy+0x288/0x600 [wl]
[ 88.973879] [cc679a80] [c9097090] wlc_phy_init+0x174/0x588 [wl]
[ 89.044860] [cc679ac0] [c919f8e4] wlc_bmac_set_extlna_pwrsave_shmem+0x28c/0xeb4 [wl]
[ 89.137717] [cc679af0] [c919bf7c] wlc_bmac_init+0xdd4/0x20e8 [wl]
[ 89.210782] [cc679b80] [c91bf088] wlc_init+0x130/0xfb8 [wl]
[ 89.277600] [cc679c00] [c91b9330] wl_init+0x34/0x60 [wl]
[ 89.341295] [cc679c10] [c91cc314] wlc_up+0x1d0/0x694 [wl]
[ 89.406030] [cc679c40] [c91b948c] wl_up+0x58/0xbc [wl]
[ 89.467649] [cc679c60] [c92a1f9c] aruba_wl_init_up+0x28/0x1f8 [wl]
[ 89.541764] [cc679c80] [c92a2390] aruba_wl_init+0x224/0x714 [wl]
[ 89.613790] [cc679ce0] [c91bcc20] wl_ams_forward_capture+0xc64/0x197c [wl]
[ 89.696241] [cc679dc0] [c92f4b44] wl_pci_probe+0x134/0x27c [wl]
[ 89.767099] [cc679dd0] [c0166f98] pci_device_probe+0x80/0xa4
[ 89.834833] [cc679df0] [c018ce54] driver_probe_device+0xa4/0x1d4
[ 89.906724] [cc679e10] [c018d040] __driver_attach+0xbc/0xc0
[ 89.973414] [cc679e30] [c018bd58] bus_for_each_dev+0x60/0x9c
[ 90.041144] [cc679e60] [c018cac0] driver_attach+0x24/0x34
[ 90.105748] [cc679e70] [c018c620] bus_add_driver+0xb0/0x268
[ 90.172431] [cc679ea0] [c018d2f4] driver_register+0x88/0x154
[ 90.240161] [cc679ec0] [c0167258] __pci_register_driver+0x54/0xe4
[ 90.313224] [cc679ee0] [c96402b4] init_module+0x2b4/0x318 [wl]
[ 90.383037] [cc679ef0] [c0001ec4] do_one_initcall+0x3c/0x1d0
[ 90.450771] [cc679f20] [c007fabc] sys_init_module+0xdc/0x1e0
[ 90.518499] [cc679f40] [c0010cc8] ret_from_syscall+0x0/0x3c
[ 90.585183] --- Exception: c01 at 0x4831cb90
[ 90.585186] LR = 0x10027830
[ 90.673742] Instruction dump:
[ 90.709176] 7c0803a6 4e800020 393d03fc 7c0004ac 7fc04f2c 813f001c 81290014 3809fff5
[ 90.801943] 2b800001 409d0050 397d03fe 7c0004ac <7c005e2c> 0c000000 4c00012c b0010008

Occasional Contributor II

Re: IAP-215 kind of died, can't convert to CAP.

Hit <Enter> to stop autoboot: 0
Booting OS partition 0
Checking image @ 0xee000000
Copying image from 0xee000000

Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
[ 0.000000] Flash variant: variant0
[ 0.000000]
[ 0.000000] Aruba Networks
[ 0.000000] ArubaOS Version 6.5.4.2 (build 61807 / label #61807)
[ 0.000000] Built by p4build@lesbos on 2017-10-07 at 00:39:00 PDT (gcc version 4.5.1)
[ 0.000000]
[ 0.000000] P1010 RDB board from Freescale Semiconductor
[ 0.000000] Memory: 248712k/262144k available (10060k kernel code, 13432k reserved, 612k data, 376k bss, 6520k init)
[ 0.001500] Brought up 1 CPUs
[ 0.078100] PCI: Probing PCI hardware
[ 0.121203] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.184002] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.246161] pci 0000:00:00.0: not setting up bridge for bus 0000:01
[ 0.320848] pci 0001:02:00.0: not setting up bridge for bus 0001:03
[ 4.923309] fsl-ifc ffe1e000.ifc: Freescale Integrated Flash Controller
[ 5.143789] irq 17: nobody cared (try booting with the "irqpoll" option)
[ 5.222960] Call Trace:
[ 5.252138] [cfff1f40] [c000853c] show_stack+0x44/0x154 (unreliable)
[ 5.328168] [cfff1f80] [c0084aac] __report_bad_irq+0x34/0xbc
[ 5.395869] [cfff1fa0] [c0084d08] note_interrupt+0x1d4/0x230
[ 5.463574] [cfff1fd0] [c0085aac] handle_fasteoi_irq+0xf4/0x13c
[ 5.534406] [cfff1ff0] [c0010654] call_handle_irq+0x18/0x28
[ 5.601064] [ce033d00] [c0004684] do_IRQ+0xcc/0x18c
[ 5.659396] [ce033d30] [c0011320] ret_from_except+0x0/0x18
[ 5.725025] --- Exception: 501 at _raw_spin_unlock_irqrestore+0x10/0x14
[ 5.725029] LR = __setup_irq+0x168/0x368
[ 5.855214] [ce033df0] [c0084488] __setup_irq+0x2c0/0x368 (unreliable)
[ 5.933334] [ce033e10] [c0084630] request_threaded_irq+0x100/0x15c
[ 6.007292] [ce033e40] [c02cc34c] fsl_ifc_ctrl_probe+0x1f4/0x2b4
[ 6.079160] [ce033e60] [c01fcc20] of_platform_device_probe+0x50/0x90
[ 6.155201] [ce033e80] [c018ce54] driver_probe_device+0xa4/0x1d4
[ 6.227066] [ce033ea0] [c018b9d0] bus_for_each_drv+0x6c/0xa8
[ 6.294770] [ce033ed0] [c018ccd8] device_attach+0xa4/0xc8
[ 6.359349] [ce033ef0] [c018c468] bus_probe_device+0x2c/0x44
[ 6.427053] [ce033f00] [c0189e0c] device_add+0x48c/0x5ec
[ 6.490599] [ce033f50] [c01fc5e8] of_device_register+0x30/0x44
[ 6.560380] [ce033f60] [c000a468] of_platform_device_create+0x44/0x74
[ 6.637457] [ce033f70] [c000a690] of_platform_bus_probe+0x12c/0x154
[ 6.712458] [ce033f90] [c037daf8] __machine_initcall_p1010_rdb_p1010rdb_publish_devices+0x38/0x48
[ 6.818695] [ce033fa0] [c0001ec4] do_one_initcall+0x3c/0x1d0
[ 6.886404] [ce033fd0] [c03759f0] kernel_init+0x1a4/0x268
[ 6.950979] [ce033ff0] [c0010a38] kernel_thread+0x4c/0x68
[ 7.015553] handlers:
[ 7.042635] [<c001ed38>] (fsl_ifc_ctrl_irq+0x0/0x1e4)
[ 7.103048] Disabling IRQ #17
[ 7.284822] ee000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank
[ 7.359965] Amd/Fujitsu Extended Query Table at 0x0040
[ 7.421456] number of CFI chips: 1
[ 7.475882] fsl-gianfar ethernet.2: enabled errata workarounds, flags: 0x4
[ 7.558285] gfar_probe: Renaming interface to bond0
[ 7.617149] /proc/gfar_bond0_stats created

[ 7.717034] Enabling watchdog on CPU 0
[ 7.763815] caam ffe30000.crypto: device ID = 0x0a14010000000000
[ 7.835808] caam ffe30000.crypto: job queues = 4
[ 7.891148] caam ffe30000.crypto: authenc-hmac-sha1-cbc-aes-caam
[ 7.963173] caam ffe30000.crypto: authenc-hmac-sha256-cbc-aes-caam
[ 8.037240] caam ffe30000.crypto: authenc-hmac-sha1-cbc-des3_ede-caam
[ 8.114462] caam ffe30000.crypto: authenc-hmac-sha256-cbc-des3_ede-caam
[ 8.193738] caam ffe30000.crypto: authenc-hmac-sha1-cbc-des-caam
[ 8.265742] caam ffe30000.crypto: authenc-hmac-sha256-cbc-des-caam
[ 8.344701] caam ffe30000.crypto: ccm-aes-caam
[ 8.442882]
[ 8.442887] Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
[ 8.534691] Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
[ 8.653631] Starting Kernel DES KAT ...Completed Kernel DES KAT
[ 8.725636] Starting Kernel AES KAT ...Completed Kernel AES KAT
[ 8.769433]
[ 8.815302] Starting Kernel HMAC SHA1 FIPS KAT ...Completed Kernel HMAC SHA1 FIPS KAT
[ 8.910616] Starting Kernel HMAC SHA256 FIPS KAT ...Completed Kernel HMAC SHA256 FIPS KAT
[ 9.032543] Starting Kernel HMAC SHA384 FIPS KAT ...Completed Kernel HMAC SHA384 FIPS KAT
[ 9.155487] Starting Kernel HMAC SHA512 FIPS KAT ...Completed Kernel HMAC SHA512 FIPS KAT
[ 9.278450] Starting Kernel AES-CBC FIPS KAT ...Completed Kernel AES-CBC FIPS KAT
[ 9.413283] Starting Kernel AES-CCM FIPS KAT ...Completed Kernel AES-CCM FIPS KAT
[ 9.513708] Starting Kernel 3DES-CBC FIPS KAT ...Completed Kernel 3DES-CBC FIPS KAT
AP-type has_ble_support: USB.
Domain Name: arubanetworks.com
No panic info available
ardmore: Start hotplug
Enabling ble_daemon via nanny
[ 18.246837] AP xml model 84, num_radios 2 (jiffies 8951)
[ 18.310483] apType 84 hw_opmode 0
[ 18.350093] radio 0: band 1 ant 0 max_ssid 16
[ 18.402204] radio 1: band 0 ant 0 max_ssid 16
[ 18.513242] init_asap_mod: installation:0
[ 18.887224] firewall cpu: core-0
ardmore: Copying BT modules to /tmp
Starting watchdog process...
Getting an IP address...
[ 23.139301] ADDRCONF(NETDEV_UP): bond0: link is not ready
[ 29.143467] PHY: bond0 (mdio@ffe24000:00) - Link is Up - 1000/Full
[ 29.248718] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
10.0.36.91 255.255.255.0 10.0.36.254
Running ADP...Done. Master is 10.0.36.253
[ 53.065065] wifi0: AP type AP-215, radio 0, max_bssids 16
[ 53.282459] aruba_usb_power_control:1136 en:1 status:0
[ 53.344043] aruba_enable_usb_block:556 Enabled USB
[ 53.401405] aruba_usb_power_control:1141 Enable USB power control for 214/215
[ 53.486877] tomatin_usb_power_control:975 enable the USB
ardmore: Insmod BT modules
[ 54.181033] usbcore: registered new interface driver usbfs
[ 54.426931] usbcore: registered new interface driver hub
[ 54.548450] usbcore: registered new device driver usb
[ 54.707025] usbcore: registered new interface driver usbserial
[ 55.001595] USB Serial support registered for generic
[ 55.062364] usbcore: registered new interface driver usbserial_generic
[ 55.140637] usbserial: USB Serial Driver core
[ 55.286816] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 55.365109] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 55.444377] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 55.587211] fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
[ 55.660863] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 55.727659] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 55.808992] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 55.895492] usb usb1: Product: Freescale On-Chip EHCI Host Controller
[ 55.972642] usb usb1: Manufacturer: Linux 2.6.35 ehci_hcd
[ 56.037290] usb usb1: SerialNumber: fsl-ehci.0

[ 56.149006] hub 1-0:1.0: USB hub found
[ 56.193956] hub 1-0:1.0: 1 port detected
[ 56.535018] usbcore: registered new interface driver cdc_acm
[ 56.602888] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
shutting down watchdog process (nanny will restart it)...

<<<<< Welcome to the Access Point >>>>>

~ #

 

So it eventually ended up in a prompt. Power led blinking green, enet blinking green faster. Amber 5GHz.

Occasional Contributor II

Re: IAP-215 kind of died, can't convert to CAP.

Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
[ 0.000000] Flash variant: variant0
[ 0.000000]
[ 0.000000] Aruba Networks
[ 0.000000] ArubaOS Version 6.5.4.2 (build 61807 / label #61807)
[ 0.000000] Built by p4build@lesbos on 2017-10-07 at 00:39:00 PDT (gcc version 4.5.1)
[ 0.000000]
[ 0.000000] P1010 RDB board from Freescale Semiconductor
[ 0.000000] Memory: 248712k/262144k available (10060k kernel code, 13432k reserved, 612k data, 376k bss, 6520k init)
[ 0.001500] Brought up 1 CPUs
[ 0.078100] PCI: Probing PCI hardware
[ 0.121203] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.184002] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.246161] pci 0000:00:00.0: not setting up bridge for bus 0000:01
[ 0.320848] pci 0001:02:00.0: not setting up bridge for bus 0001:03
[ 4.923309] fsl-ifc ffe1e000.ifc: Freescale Integrated Flash Controller
[ 5.143789] irq 17: nobody cared (try booting with the "irqpoll" option)
[ 5.222960] Call Trace:
[ 5.252138] [cfff1f40] [c000853c] show_stack+0x44/0x154 (unreliable)
[ 5.328168] [cfff1f80] [c0084aac] __report_bad_irq+0x34/0xbc
[ 5.395869] [cfff1fa0] [c0084d08] note_interrupt+0x1d4/0x230
[ 5.463574] [cfff1fd0] [c0085aac] handle_fasteoi_irq+0xf4/0x13c
[ 5.534406] [cfff1ff0] [c0010654] call_handle_irq+0x18/0x28
[ 5.601064] [ce033d00] [c0004684] do_IRQ+0xcc/0x18c
[ 5.659396] [ce033d30] [c0011320] ret_from_except+0x0/0x18
[ 5.725025] --- Exception: 501 at _raw_spin_unlock_irqrestore+0x10/0x14
[ 5.725029] LR = __setup_irq+0x168/0x368
[ 5.855214] [ce033df0] [c0084488] __setup_irq+0x2c0/0x368 (unreliable)
[ 5.933334] [ce033e10] [c0084630] request_threaded_irq+0x100/0x15c
[ 6.007292] [ce033e40] [c02cc34c] fsl_ifc_ctrl_probe+0x1f4/0x2b4
[ 6.079160] [ce033e60] [c01fcc20] of_platform_device_probe+0x50/0x90
[ 6.155201] [ce033e80] [c018ce54] driver_probe_device+0xa4/0x1d4
[ 6.227066] [ce033ea0] [c018b9d0] bus_for_each_drv+0x6c/0xa8
[ 6.294770] [ce033ed0] [c018ccd8] device_attach+0xa4/0xc8
[ 6.359349] [ce033ef0] [c018c468] bus_probe_device+0x2c/0x44
[ 6.427053] [ce033f00] [c0189e0c] device_add+0x48c/0x5ec
[ 6.490599] [ce033f50] [c01fc5e8] of_device_register+0x30/0x44
[ 6.560380] [ce033f60] [c000a468] of_platform_device_create+0x44/0x74
[ 6.637457] [ce033f70] [c000a690] of_platform_bus_probe+0x12c/0x154
[ 6.712458] [ce033f90] [c037daf8] __machine_initcall_p1010_rdb_p1010rdb_publish_devices+0x38/0x48
[ 6.818695] [ce033fa0] [c0001ec4] do_one_initcall+0x3c/0x1d0
[ 6.886404] [ce033fd0] [c03759f0] kernel_init+0x1a4/0x268
[ 6.950979] [ce033ff0] [c0010a38] kernel_thread+0x4c/0x68
[ 7.015553] handlers:
[ 7.042635] [<c001ed38>] (fsl_ifc_ctrl_irq+0x0/0x1e4)
[ 7.103048] Disabling IRQ #17
[ 7.284822] ee000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank
[ 7.359965] Amd/Fujitsu Extended Query Table at 0x0040
[ 7.421456] number of CFI chips: 1
[ 7.475882] fsl-gianfar ethernet.2: enabled errata workarounds, flags: 0x4
[ 7.558285] gfar_probe: Renaming interface to bond0
[ 7.617149] /proc/gfar_bond0_stats created
[ 7.717034] Enabling watchdog on CPU 0
[ 7.763815] caam ffe30000.crypto: device ID = 0x0a14010000000000
[ 7.835808] caam ffe30000.crypto: job queues = 4

[ 7.891148] caam ffe30000.crypto: authenc-hmac-sha1-cbc-aes-caam
[ 7.963173] caam ffe30000.crypto: authenc-hmac-sha256-cbc-aes-caam
[ 8.037240] caam ffe30000.crypto: authenc-hmac-sha1-cbc-des3_ede-caam
[ 8.114462] caam ffe30000.crypto: authenc-hmac-sha256-cbc-des3_ede-caam
[ 8.193738] caam ffe30000.crypto: authenc-hmac-sha1-cbc-des-caam
[ 8.265742] caam ffe30000.crypto: authenc-hmac-sha256-cbc-des-caam
[ 8.344701] caam ffe30000.crypto: ccm-aes-caam
[ 8.442882]
[ 8.442887] Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
[ 8.534691] Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
[ 8.653631] Starting Kernel DES KAT ...Completed Kernel DES KAT
[ 8.725636] Starting Kernel AES KAT ...Completed Kernel AES KAT
[ 8.769433]
[ 8.815302] Starting Kernel HMAC SHA1 FIPS KAT ...Completed Kernel HMAC SHA1 FIPS KAT
[ 8.910616] Starting Kernel HMAC SHA256 FIPS KAT ...Completed Kernel HMAC SHA256 FIPS KAT
[ 9.032543] Starting Kernel HMAC SHA384 FIPS KAT ...Completed Kernel HMAC SHA384 FIPS KAT
[ 9.155487] Starting Kernel HMAC SHA512 FIPS KAT ...Completed Kernel HMAC SHA512 FIPS KAT
[ 9.278450] Starting Kernel AES-CBC FIPS KAT ...Completed Kernel AES-CBC FIPS KAT
[ 9.413283] Starting Kernel AES-CCM FIPS KAT ...Completed Kernel AES-CCM FIPS KAT
[ 9.513708] Starting Kernel 3DES-CBC FIPS KAT ...Completed Kernel 3DES-CBC FIPS KAT
AP-type has_ble_support: USB.
Domain Name: arubanetworks.com
No panic info available
ardmore: Start hotplug
Enabling ble_daemon via nanny
[ 18.246837] AP xml model 84, num_radios 2 (jiffies 8951)
[ 18.310483] apType 84 hw_opmode 0
[ 18.350093] radio 0: band 1 ant 0 max_ssid 16
[ 18.402204] radio 1: band 0 ant 0 max_ssid 16
[ 18.513242] init_asap_mod: installation:0
[ 18.887224] firewall cpu: core-0
ardmore: Copying BT modules to /tmp
Starting watchdog process...
Getting an IP address...
[ 23.139301] ADDRCONF(NETDEV_UP): bond0: link is not ready
[ 29.143467] PHY: bond0 (mdio@ffe24000:00) - Link is Up - 1000/Full
[ 29.248718] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
10.0.36.91 255.255.255.0 10.0.36.254
Running ADP...Done. Master is 10.0.36.253
[ 53.065065] wifi0: AP type AP-215, radio 0, max_bssids 16
[ 53.282459] aruba_usb_power_control:1136 en:1 status:0
[ 53.344043] aruba_enable_usb_block:556 Enabled USB
[ 53.401405] aruba_usb_power_control:1141 Enable USB power control for 214/215
[ 53.486877] tomatin_usb_power_control:975 enable the USB
ardmore: Insmod BT modules
[ 54.181033] usbcore: registered new interface driver usbfs
[ 54.426931] usbcore: registered new interface driver hub
[ 54.548450] usbcore: registered new device driver usb
[ 54.707025] usbcore: registered new interface driver usbserial
[ 55.001595] USB Serial support registered for generic
[ 55.062364] usbcore: registered new interface driver usbserial_generic
[ 55.140637] usbserial: USB Serial Driver core
[ 55.286816] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 55.365109] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller

[ 55.444377] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 55.587211] fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
[ 55.660863] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 55.727659] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 55.808992] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 55.895492] usb usb1: Product: Freescale On-Chip EHCI Host Controller
[ 55.972642] usb usb1: Manufacturer: Linux 2.6.35 ehci_hcd
[ 56.037290] usb usb1: SerialNumber: fsl-ehci.0
[ 56.149006] hub 1-0:1.0: USB hub found
[ 56.193956] hub 1-0:1.0: 1 port detected
[ 56.535018] usbcore: registered new interface driver cdc_acm
[ 56.602888] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
shutting down watchdog process (nanny will restart it)...

<<<<< Welcome to the Access Point >>>>>

~ #

 

So it eventually ended up in a prompt. Power blinking green, enet blinking faster green, 5GHz amber.

Highlighted
Guru Elite

Re: IAP-215 kind of died, can't convert to CAP.

Please contact TAC for what you should do next:

http://www.arubanetworks.com/support-services/contact-support/



Colin Joseph
Aruba Customer Engineering

Looking for an Answer? Search the Community Knowledge Base Here: Community Knowledge Base

Occasional Contributor II

Re: IAP-215 kind of died, can't convert to CAP.

Thanks. I will get a replacement.

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: