Hi,every one, I am a new about aruba,
Here is my Master / Local LAB ,
Master ver : ArubaOS (MODEL: Aruba6000), Version 6.4.3.9 IP : 192.168.71.217
Local ver : ArubaOS (MODEL: Aruba7210), Version 6.4.3.9 IP : 192.168.71.218
All Switches
------------
IP Address Name Location Type Model Version Status Configuration State Config Sync Time (sec) Config ID
---------- ---- -------- ---- ----- ------- ------ ------------------- ---------------------- ---------
192.168.71.217 Aruba6000 Building1.floor1 master Aruba6000 6.4.3.9_55230 up UPDATE SUCCESSFUL 0 29
192.168.71.218 Aruba7210 Building1.floor1 local Aruba7210 6.4.3.9_55230 up UPDATE SUCCESSFUL 2 29
Total Switches:2
--------------------------------
When I set an AP-105 use remote AP mode, and I config the LMS profile , there is an strange thing about the ap config,
-------------------------------
here is the ap database display
AP Database
-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP
---- ----- ------- ---------- ------ ----- --------- ----------
My-test-001 Group-Jace_test 105 10.10.217.24 Up 1h:30m:40s Rc2 192.168.71.217 0.0.0.0
===============
here is my group config
AP group "Group-Jace_test"
--------------------------
Parameter Value
--------- -----
Virtual AP VAP-Mydot1x
802.11a radio profile default
802.11g radio profile default
Ethernet interface 0 port configuration default
Ethernet interface 1 port configuration default
Ethernet interface 2 port configuration shutdown
Ethernet interface 3 port configuration shutdown
Ethernet interface 4 port configuration shutdown
AP system profile apsys_LMStest
VoIP Call Admission Control profile default
802.11a Traffic Management profile N/A
802.11g Traffic Management profile N/A
Regulatory Domain profile default
RF Optimization profile default
RF Event Thresholds profile default
IDS profile default
Mesh Radio profile default
Mesh Cluster profile N/A
Provisioning profile N/A
AP authorization profile N/A
================
I set the group's ap-system file use "apsys_LMStest" , but when I check the ap config, it shows different
(Aruba6000) #show ap config ap-name My-test-001
Configuration for AP name "My-test-001" AP group "Group-Jace_test"
------------------------------------------------------------------
Parameter 802.11g 802.11a Source
--------- ------- ------- ------
RF Band g g ap system-profile "apsys_default"
RF Band for AM mode scanning all all ap system-profile "apsys_default"
Native VLAN ID 1 1 ap system-profile "apsys_default"
Tunnel Heartbeat Interval 1 1 ap system-profile "apsys_default"
Session ACL ap-uplink-acl ap-uplink-acl ap system-profile "apsys_default"
SNMP sysContact N/A N/A ap system-profile "apsys_default"
LED operating mode (11n/11ac APs only) normal normal ap system-profile "apsys_default"
LED override Disabled Disabled ap system-profile "apsys_default"
Driver log level emergencies emergencies ap system-profile "apsys_default"
SAP MTU N/A N/A ap system-profile "apsys_default"
RAP MTU 1200 bytes 1200 bytes ap system-profile "apsys_default"
LMS IP 192.168.71.217 192.168.71.217 ap system-profile "apsys_default"
Backup LMS IP 192.168.71.218 192.168.71.218
===================
so I can't move the AP to Local-controller
could anyone provide some suggestion for me,
Thank you !