Hello
sw-arb01(config)#
sh interface 1/1/10Interface 1/1/10 is up
Admin state is up
Link state: up for 1 minute (since Wed Oct 13 12:40:00 CEST 2021)
Link transitions: 75
Description:
Hardware: Ethernet, MAC Address: 38:10:xx:xx:xx:xx
MTU 1500
Type 1GbT
Full-duplex
qos trust cos
Speed 100 Mb/s
Auto-negotiation is on
Energy-Efficient Ethernet is disabled
Flow-control: off
Error-control: off
MDI mode: MDI
VLAN Mode: access
Access VLAN: 1
Rate collection interval: 300 seconds
Rate RX TX Total (RX+TX)
---------------- -------------------- -------------------- --------------------
Mbits / sec 0.00 0.02 0.02
KPkts / sec 0.00 0.02 0.02
Unicast 0.00 0.00 0.00
Multicast 0.00 0.01 0.01
Broadcast 0.00 0.01 0.01
Utilization 0.00 0.02 0.02
Statistic RX TX Total
---------------- -------------------- -------------------- --------------------
Packets 715668 3442753 4158421
Unicast 572704 147754 720458
Multicast 1018 1825103 1826121
Broadcast 141946 1469896 1611842
Bytes 47004636 535176593 582181229
Jumbos 0 0 0
Dropped 0 0 0
Pause Frames 0 0 0
Errors 0 0 0
CRC/FCS 0 n/a 0
Collision n/a 0 0
Runts 0 n/a 0
Giants 0 n/a 0
sw-arb01(config)#
show mac-address-table port 1/1/10MAC age-time : 300 seconds
Number of MAC addresses : 1
MAC Address VLAN Type Port
--------------------------------------------------------------
00:09:40:xx:xx:xx 1 dynamic 1/1/10
sw-arb01(config)#
sh vlan 100------------------------------------------------------------------------------------------------------------------
VLAN Name Status Reason Type Interfaces
------------------------------------------------------------------------------------------------------------------
100 VLAN100 up ok static 1/1/2
sw-arb01(config)#
show port-access device-profileProfile Name : test_profile
LLDP Groups :
CDP Groups :
MAC Groups : test
Role : test_role
State : Enabled
sw-arb01(config)#
sh port-access device-profile interface allNo device-profile clients found.
regards
David
------------------------------
David
------------------------------
Original Message:
Sent: Oct 13, 2021 05:45 AM
From: Ivan Bondar
Subject: Voice VLAN based on MAC range or Mac-OUI in 6200F or 6100
Could you connect the phone to the switch, wait for it to get IP from VLAN 1 and send me the output of the following commands:
show interface <phone_port>show mac-address-table port <phone_port>show vlan 100show port-access device-profileshow port-access device-profile interface all
------------------------------
Ivan Bondar
Original Message:
Sent: Oct 13, 2021 05:13 AM
From: David Lawson
Subject: Voice VLAN based on MAC range or Mac-OUI in 6200F or 6100
Hello
that's exactly what I did and it doesn't work. I really don't know anymore.
#mac-group test
mac-oui 00:09:40
#port-access role test_role
vlan access 100
#port-access device-profile profile01
enable
associate mac-group test
associate role test_role
Phone still stays in vlan 1.
I really don't know anymore.
regards
------------------------------
David
Original Message:
Sent: Oct 13, 2021 04:48 AM
From: Ivan Bondar
Subject: Voice VLAN based on MAC range or Mac-OUI in 6200F or 6100
Hello David,
It seems the 'Device Profiles' feature is what you are looking for. Check the Fundamentals Guide for 6200 - https://www.arubanetworks.com/techdocs/AOS-CX/10.08/HTML/fundamentals_6200/Content/Chp_Dev_disc/dev-pro-fl-m-10.htm 'Configuring a device profile for local MAC match' section.
------------------------------
Ivan Bondar
Original Message:
Sent: Oct 13, 2021 04:24 AM
From: David Lawson
Subject: Voice VLAN based on MAC range or Mac-OUI in 6200F or 6100
Hello
In Cisco switches, it is possible to configure voice vlan based on MAC address only.
Even if the phone doesn't support LLDP, CDP or can't tag traffic, we can still place it in the voice vlan based on the MAC range without touching the phone.
is there any way to configure the same in Aruba AOS-CX 10.08 switches like 6200f or 6100 to move a phone in a vlan based only on its mac-OU?
which command ?
Thanks
------------------------------
David
------------------------------