Hi,
I have reseted both. The fastest AP advertise the SSID "SetMeUp" and on the second AP only the power LED lights up.
AP1:
90:4c:81:c5:07:dc# show ap-env
Antenna Type:Internal
Need USB field:Yes
ipaddr:192.168.1.233
netmask:255.255.255.0
gatewayip:192.168.1.1
dnsip:192.168.1.14
domainname:XXXX.local
90:4c:81:c5:07:dc# show swarm mode
Swarm Mode :Cluster
90:4c:81:c5:07:dc# sh swarm state
AP Swarm State :swarm_config_sync_complete
mesh auto eth0 bridging :no
Config in flash :yes
factory SSID in flash :yes
extended-ssid configured :yes
extended-ssid active :yes
advanced-zone configured :no
Factory default status :no
Source of system time :NTP server
Config load cnt :1
VC Channel index :1
IDS Client Gateway Detect :yes
Config Init success cnt for heartbeat :0
Config Init success cnt for register :0
Config Init skipping cnt for heartbeat :0
Config Init skipping cnt for register :0
Config Init last success reason :N/A
Config Init last success time :N/A
Radio down state :0x0 / 0x0
Thermal Protect state :None
AP2:
cc:d0:83:c0:18:a8# sh ap-env
Antenna Type:Internal
Need USB field:Yes
uap_controller_less:1
cc:d0:83:c0:18:a8# sh swarm mode
Swarm Mode :Cluster
############################
Ping from AP1 to AP2
90:4c:81:c5:07:dc# ping 192.168.1.234
Press 'q' to abort.
PING 192.168.1.234 (192.168.1.234): 56 data bytes
64 bytes from 192.168.1.234: icmp_seq=0 ttl=64 time=0.6 ms
64 bytes from 192.168.1.234: icmp_seq=1 ttl=64 time=0.6 ms
64 bytes from 192.168.1.234: icmp_seq=2 ttl=64 time=0.6 ms
64 bytes from 192.168.1.234: icmp_seq=3 ttl=64 time=0.6 ms
64 bytes from 192.168.1.234: icmp_seq=4 ttl=64 time=0.6 ms
--- 192.168.1.234 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0.6/0.6/0.6 ms
Thank you
------------------------------
Michael Schlarb
------------------------------
Original Message:
Sent: Jul 11, 2021 02:41 AM
From: Gorazd Kikelj
Subject: Clustering 2x IAP-305 fails
Try to factory reset both and then connect to setmeup ssid. It should not matter if there will be different FW versions as it will be synchronized during cluster setup.
It can be that one AP has standalone variable set to 1 and will not join the cluster. Without console cable you can check it from cli with show ap-env or from GUI Support tab. For this to check, you need to connect only on AP at a time so that won't get stuck in cluster setup if that is the case.
Did you try to ssh to APs?
Best, Gorazd
------------------------------
Gorazd Kikelj
Original Message:
Sent: Jul 04, 2021 07:02 AM
From: Michael Schlarb
Subject: Clustering 2x IAP-305 fails
Hello Community,
I have some trubble to connect (cluster) one new IAP-305 to an exciting IAP-305. Both running on same Firmware version 8.7.1.3_79817.
Cluster Security -> disabled
Auto Join mode -> enabled
Both running on same L2 network
And they are connectet to the same D-Link DGS-1510-28P switch.
I've also factory reseted the existing IAP without any changes.
I also read some HowTo's without success.
Can someone help me?
Many thanks
------------------------------
Michael Schlarb
------------------------------