Problem:Under the command "show ap debug lacp ap-name <name of the AP>" I see the GRE striping IP as 0.0.0.0.
What could be the reason behind this and how to correct it?
Diagnostics:1. See if AP lacp striping IP is enabled.
2. Verify if unique striping IP in controller IP's subnet is provided.
3. Confirm if the LMS is also -provided in AP sytem profile.
(Aruba7210) # show ap-lacp-striping-ip
AP LACP LMS map information
---------------------------
Parameter Value
--------- -----
AP LACP Striping IP Enabled
GRE Striping IP 10.1.1.103 LMS 10.1.1.3
4. See if the AP system profile has the correct LMS ip mentioned:
(Master) #show ap database
AP Database
-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP
---- ----- ------- ---------- ------ ----- --------- ----------
9c:1c:12:c0:a2:e4 10.1.1.3 225 10.1.1.251 Up 19m:2s 10.1.1.3 0.0.0.0
Flags: U = Unprovisioned; N = Duplicate name; G = No such group; L = Unlicensed
I = Inactive; D = Dirty or no config; E = Regulatory Domain Mismatch
X = Maintenance Mode; P = PPPoE AP; B = Built-in AP; s = LACP striping
R = Remote AP; R- = Remote AP requires Auth; C = Cellular RAP;
c = CERT-based RAP; 1 = 802.1x authenticated AP; 2 = Using IKE version 2
u = Custom-Cert RAP; S = Standby-mode AP; J = USB cert at AP
i = Indoor; o = Outdoor
M = Mesh node; Y = Mesh Recovery
Total APs:1
(Master) # ap-regroup ap-name 9c:1c:12:c0:a2:e4 default
NOTE: For cert RAP ap-group specified in RAP whitelist will take precedence.
(Master) #show ap-group default
AP group "default"
------------------
Parameter Value
--------- -----
Virtual AP default
Virtual AP 40Mhz
Virtual AP 20Mhz
802.11a radio profile default
802.11g radio profile default
Ethernet interface 0 port configuration default
Ethernet interface 1 port configuration default
Ethernet interface 2 port configuration shutdown
Ethernet interface 3 port configuration shutdown
Ethernet interface 4 port configuration shutdown
AP system profile default
VoIP Call Admission Control profile default
<snip>
(Master) # show ap system-profile default
AP system profile "default"
---------------------------
Parameter Value
--------- -----
RF Band g
RF Band for AM mode scanning all
Native VLAN ID 1
Tunnel Heartbeat Interval 1
Session ACL ap-uplink-acl
Corporate DNS Domain N/A
SNMP sysContact N/A
LED operating mode (11n/11ac APs only) normal
LED override Disabled
Driver log level emergencies
SAP MTU N/A
RAP MTU 1200 bytes
LMS IP N/A
Backup LMS IP N/A
<snip>
Solution1. Enable AP lacp, give correct GRE striping IP and lms IP on the controller:
(Aruba7210) #configure t
(Aruba7210) (config) #ap-lacp-striping-ip
(Aruba7210) (AP LACP LMS map information) #aplacp-enable
(Aruba7210) (AP LACP LMS map information) #striping-ip 10.1.1.103 lms 10.1.1.3
2. configure the same lms IP in corresponding ap system profile:
(Master) #configure t
(Master) (config) #ap system-profile default
(Master) (AP system profile "default") #lms-ip 10.1.1.3
(Master) (AP system profile "default") #write memory