Hi, if i am tagging the port in vlan 4 i can do this, with no problem. The problem is when i try to untagg from vlan1. It dosen't come out from untagged vlan1 so that i can put untagged in vlan4.
Sim:
ArubaVSF_1# sho runn int 1/20
Running configuration:
interface 1/20
untagged vlan 1
exit
ArubaVSF_1# conf t
ArubaVSF_1(config)# int 1/20
ArubaVSF_1(eth-1/20)# tagg vlan 4
ArubaVSF_1(eth-1/20)# sho runn int 1/20
Running configuration:
interface 1/20
tagged vlan 4
untagged vlan 1
exit
ArubaVSF_1(eth-1/20)# no tagged vlan 4
ArubaVSF_1(eth-1/20)# sho runn int 1/20
Running configuration:
interface 1/20
untagged vlan 1
exit
ArubaVSF_1(eth-1/20)# untagg vlan 4
4: Inconsistent value.
ArubaVSF_1(eth-1/20)#
ArubaVSF_1(eth-1/20)# sho runn int 1/20
Running configuration:
interface 1/20
untagged vlan 1
exit
ArubaVSF_1(eth-1/20)#
------------------------------
Dragos Ilie
------------------------------
Original Message:
Sent: Mar 30, 2021 11:43 AM
From: Davide Poletto
Subject: 2930F Untagged Vlan
Hi Dragos, does it let you to tag the port 1/20 with VLAN id 4? I mean...instead of changing the untagged VLAN id (PVID)...that's to see if the issue if with "untagging" the port only or it happens too with "tagging" the port with that particular VLAN id...what client are you using to perform CLI commands? PuTTY SSH? PuTTY direct Serial? other? maybe a bug in WC.16.10.0010? pretty strange.
Have you tried to reboot the switch or to perform the same operation through the CLI Menu mode? in any case save the running configuration. It the running configuration file "clean"?
------------------------------
Davide Poletto
Original Message:
Sent: Mar 30, 2021 11:15 AM
From: Dragos Ilie
Subject: 2930F Untagged Vlan
Maybe it can be something phisical? I don't know..i am afraid to upgrade firmware from #WC.16.10.0010 to WC_16_10_0012. Maybe the upgrade will help me?
Thank you.
------------------------------
Dragos Ilie
Original Message:
Sent: Mar 30, 2021 10:38 AM
From: Dragos Ilie
Subject: 2930F Untagged Vlan
Hi, thank you for the info. Still i cannot do untagged port to vlan:
==========this is vlan 4=================<o:p></o:p>
ArubaVSF_1# sho runn vlan 4
Running configuration:
vlan 4
name "VOIP"
tagged 1/6,1/25-1/33,2/6,2/13-2/17,2/46,Trk1-Trk2,Trk4-Trk9
untagged 1/22
ip address 192.168.4.254 255.255.254.0
ipv6 enable
ipv6 address autoconfig
exit<o:p></o:p>
==============this is port 1/20===================
ArubaVSF_1# sho runn int 1/20
Running configuration:
interface 1/20
untagged vlan 1
exit<o:p></o:p>
==========triyng from port to vlan============
ArubaVSF_1# conf t
ArubaVSF_1(config)# int 1/20
ArubaVSF_1(eth-1/20)# untagged vlan 4
4: Inconsistent value.
ArubaVSF_1(eth-1/20)# end
ArubaVSF_1# sho runn int 1/20
Running configuration:
interface 1/20
untagged vlan 1
exit<o:p></o:p>
=========trying from vlan 4 to port============
ArubaVSF_1# conf t
ArubaVSF_1(config)# vlan 4
ArubaVSF_1(vlan-4)# untagged 1/20
1/20: Inconsistent value.
ArubaVSF_1(vlan-4)# end
ArubaVSF_1# sho runn vlan 4
Running configuration:
vlan 4
name "VOIP"
tagged 1/6,1/25-1/33,2/6,2/13-2/17,2/46,Trk1-Trk2,Trk4-Trk9
untagged 1/22
ip address 192.168.4.254 255.255.254.0
ipv6 enable
ipv6 address autoconfig
exit<o:p></o:p>
------------------------------
Dragos Ilie
Original Message:
Sent: Mar 26, 2021 01:08 PM
From: Ciro Gustavo Mele
Subject: 2930F Untagged Vlan
Hi,
Try to change the configuration from the vlan not from the port
Check if there is an ip assigned to the vlan
In the manual I send you are all the aruba switch event messages
Good Luck !
Ciro Gustavo Mele
------------------------------
Ciro Gustavo Mele
Original Message:
Sent: Mar 25, 2021 10:16 AM
From: Dragos Ilie
Subject: 2930F Untagged Vlan
Hello, i have a situation with switch model Aruba 2930F. I want to assign a port(ex 20) to an untagged vlan, let's say on vlan4.
Initial status for port 20:
1. ArubaVSF_1# sho runn int 1/20
Ru1nning configuration:
interface 1/20
untagged vlan 1
exit
2. Triyng to put untagged vlan4 on port20:
ArubaVSF_1# conf t
ArubaVSF_1(config)# int 1/20
ArubaVSF_1(eth-1/20)# untagged vlan 4
4: Inconsistent value.
ArubaVSF_1(eth-1/20)# untag vlan 99
99: Inconsistent value
3. If am triyng to put port20 tagged on vlan4 it let me:
ArubaVSF_1(eth-1/20)# tagg vlan 4
ArubaVSF_1(eth-1/20)# sho runn int 1/20
Running configuration:
interface 1/20
tagged vlan 4
untagged vlan 1
exit
4. I'm removing tagging from vlan4:
ArubaVSF_1(eth-1/20)# no tagg vlan 4
ArubaVSF_1(eth-1/20)# sho runn int 1/20
Running configuration:
interface 1/20
untagged vlan 1
exit
5. Triyng to put untagged on vlan10 for ex.:
ArubaVSF_1(eth-1/20)# untagged vlan 10
10: Inconsistent value.
ArubaVSF_1(eth-1/20)#
I need some help, i have 2 switches(2930F) in vsf stack. I just want to assign any port(20 for ex.) untagged on any vlan(let's say 4), what is with 'Inconsistent value'? On another switch(2930F) which dosen't belong to vsf, it is in another configuration scheme , i can do this. Is it true that i have another firmware version on the switch that i can do untagged. Those in vsf stack have #WC.16.10.0010 version.
I also attached configuration.
Thank you in advance!
------------------------------
Dragos Ilie
------------------------------