Wired Intelligent Edge

 View Only
last person joined: yesterday 

Bring performance and reliability to your network with the Aruba Core, Aggregation, and Access layer switches. Discuss the latest features and functionality of the ArubaOS-Switch and ArubaOS-CX devices, and find ways to improve security across your network to bring together a mobile first solution.
Expand all | Collapse all

6300M switch

This thread has been viewed 25 times
  • 1.  6300M switch

    Posted Jul 13, 2022 01:43 PM
    I've been looking for a command for my 6300M switches that would show real time statistics on a port.
    Does anyone out there know if such a command exists?
    I tried all the "show interface 1/1/28" different options but none seem to give me what I'm looking for.
    More specifically I'm trying to determine if the port is being saturated.

    commands I've tried:
    # show interface 1/1/28
    brief Show information in brief format
    dom Show transceiver diagnostics information
    downshift-enable Show downshift-enable information
    error-statistics Show interface error statistics
    extended Show additional interface statistics
    fault-monitor Show fault monitor information
    link-status Show link status information
    physical Show physical interface information
    qos Show QoS info for the interface
    queues Show tx queue info for the interface
    statistics Show interface statistics
    transceiver Show transceiver information
    <cr>


    Any assistance is greatly appreciated

    ------------------------------
    Gerardo
    ------------------------------


  • 2.  RE: 6300M switch

    EMPLOYEE
    Posted Jul 13, 2022 04:39 PM
    I normally use this

    PE2# sh int 1/1/15 | b Rate
    Rate collection interval: 300 seconds

    Rate RX TX Total (RX+TX)
    ---------------- -------------------- -------------------- --------------------
    Mbits / sec 328.40 328.40 656.80
    KPkts / sec 554.73 554.73 1109.46
    Unicast 554.73 554.73 1109.46
    Multicast 0.00 0.00 0.00
    Broadcast 0.00 0.00 0.00
    Utilization % 3.28 3.28 6.56

    ------------------------------
    DWan
    ------------------------------



  • 3.  RE: 6300M switch

    MVP GURU
    Posted Jul 14, 2022 05:44 AM
    Hi DWan, we have a way to see Tx/Rx rate values also for a LAG (MC or not) logical interface? unfortunately the output of show interface lag <lag-id> reports in tabular forms only Statistic values and not also Rate values...


  • 4.  RE: 6300M switch

    Posted Jul 14, 2022 10:58 AM
    Hi Daryl,
    As the previous comment mentioned, that command on the 6300M switch only provides us with the static values.
    Here is an example of the output:

    CB2# show interface 1/1/28 | b Rate
    Type 5G-SmartRate
    Full-duplex
    qos trust none
    Speed 1000 Mb/s
    Auto-negotiation is on
    Flow-control: off
    Error-control: off
    MDI mode: MDI
    VLAN Mode: access
    Access VLAN: 1126
    Rx
    12904901 total packets 1438149939 total bytes
    12302355 unicast packets
    602424 multicast packets
    122 broadcast packets
    0 errors 0 dropped
    0 CRC/FCS
    Tx
    73713888 total packets 9423144384 total bytes
    23836578 unicast packets
    33676316 multicast packets
    16200994 broadcast packets
    0 errors 3 dropped
    0 collision




  • 5.  RE: 6300M switch

    MVP GURU
    Posted Jul 14, 2022 12:41 PM
    On a AOS-CX 10.08 (Aruba 8360) I can see this on a simple physical interface (Tx/Rx rates on the LAG aren't available, only statistics):


    Aren't you able to see a similar output on your Aruba 6300 with the very same command applied to a single physical interface?


  • 6.  RE: 6300M switch

    Posted Jul 14, 2022 01:11 PM
    I don't see that output on the my 6300m or on my 8325

    I'm running 
    Version      : FL.10.05.0021.    on my 6300m
    and
    Version      : GL.10.05.0011.    on my 8325








  • 7.  RE: 6300M switch

    EMPLOYEE
    Posted Jul 14, 2022 12:56 PM

    I think this is due to software release, you could be running older code that doesn't show the rate.

    Try upgrading if possible.



    ------------------------------
    DWan
    ------------------------------



  • 8.  RE: 6300M switch

    Posted Jul 14, 2022 01:19 PM
    Can confirm that output on 8325 running 10.09 matches what parnassus sees..​


  • 9.  RE: 6300M switch

    MVP GURU
    Posted Jul 14, 2022 02:49 PM
    So it's just a matter of upgrading those Aruba CX switches to a supported ArubaOS-CX version (currently AOS-CX 10.06, 10.07, 10.08, 10.09 or 10.10...with a preferece, I add, for 10.09 SSR and 10.10 LSR): among other things AOS-CX 10.05 is unsupported and had been deprecated and Aruba customers were properly advised to upgrade to newer supported ArubaOS-CX releases.