Wireless Access

Is there a way to adjust the RF settings for, 2.4 and 5, on an individual AP without affecting those same settings on an entire AP group? We have a few APs that we'd like to keep in the same AP group but need higher RF settings.

Thank you.

------------------------------
Nathan K
------------------------------

You can configure this like the screenshot below. You can link to different radio profiles on a per AP basis.

IMPORTANT!!!   Create new radio profiles for this. Manipulating an existing profile can effect the AP-groups that are using it.

------------------------------
Dustin Burns

Lead Mobility Engineer @Worldcom Exchange, Inc.

ACCX 1271| ACMX 509| ACSP | ACDA | MVP Guru 2022-2023
If my post was useful accept solution and/or give kudos

Original Message:
Sent: May 08, 2023 07:52 AM
From: nkuhl1630
Subject: Adjust RF on an Individual AP

Is there a way to adjust the RF settings for, 2.4 and 5, on an individual AP without affecting those same settings on an entire AP group? We have a few APs that we'd like to keep in the same AP group but need higher RF settings.

Thank you.

------------------------------
Nathan K
------------------------------

Thanks. I knew you could do it but wasn't sure exactly how. We're running AOS 8. Is it possible to do this in the GUI as well? I couldn't find the right view.

You can configure this like the screenshot below. You can link to different radio profiles on a per AP basis.

IMPORTANT!!!   Create new radio profiles for this. Manipulating an existing profile can effect the AP-groups that are using it.

------------------------------
Dustin Burns

Lead Mobility Engineer @Worldcom Exchange, Inc.

ACCX 1271| ACMX 509| ACSP | ACDA | MVP Guru 2022-2023
If my post was useful accept solution and/or give kudos

Original Message:
Sent: May 08, 2023 07:52 AM
From: nkuhl1630
Subject: Adjust RF on an Individual AP

Is there a way to adjust the RF settings for, 2.4 and 5, on an individual AP without affecting those same settings on an entire AP group? We have a few APs that we'd like to keep in the same AP group but need higher RF settings.

Thank you.

------------------------------
Nathan K
------------------------------

No just CLI.

Thanks. I knew you could do it but wasn't sure exactly how. We're running AOS 8. Is it possible to do this in the GUI as well? I couldn't find the right view.

You can configure this like the screenshot below. You can link to different radio profiles on a per AP basis.

IMPORTANT!!!   Create new radio profiles for this. Manipulating an existing profile can effect the AP-groups that are using it.

------------------------------
Dustin Burns

Lead Mobility Engineer @Worldcom Exchange, Inc.

ACCX 1271| ACMX 509| ACSP | ACDA | MVP Guru 2022-2023
If my post was useful accept solution and/or give kudos

Original Message:
Sent: May 08, 2023 07:52 AM
From: nkuhl1630
Subject: Adjust RF on an Individual AP

Is there a way to adjust the RF settings for, 2.4 and 5, on an individual AP without affecting those same settings on an entire AP group? We have a few APs that we'd like to keep in the same AP group but need higher RF settings.

Thank you.

------------------------------
Nathan K
------------------------------

I thought there was per AP overide in AOS 8.8  that you could make use of through WebUI. Perhaps you can check that.

No just CLI.

Thanks. I knew you could do it but wasn't sure exactly how. We're running AOS 8. Is it possible to do this in the GUI as well? I couldn't find the right view.

You can configure this like the screenshot below. You can link to different radio profiles on a per AP basis.

IMPORTANT!!!   Create new radio profiles for this. Manipulating an existing profile can effect the AP-groups that are using it.

------------------------------
Dustin Burns

Lead Mobility Engineer @Worldcom Exchange, Inc.

ACCX 1271| ACMX 509| ACSP | ACDA | MVP Guru 2022-2023
If my post was useful accept solution and/or give kudos

Original Message:
Sent: May 08, 2023 07:52 AM
From: nkuhl1630
Subject: Adjust RF on an Individual AP

Is there a way to adjust the RF settings for, 2.4 and 5, on an individual AP without affecting those same settings on an entire AP group? We have a few APs that we'd like to keep in the same AP group but need higher RF settings.

Thank you.

------------------------------
Nathan K
------------------------------

Thanks. We're still on 8.7.1.10 and plan to upgrade to 8.10 in a few weeks. I'll take a look at this then.

I thought there was per AP overide in AOS 8.8  that you could make use of through WebUI. Perhaps you can check that.

No just CLI.

Thanks. I knew you could do it but wasn't sure exactly how. We're running AOS 8. Is it possible to do this in the GUI as well? I couldn't find the right view.

You can configure this like the screenshot below. You can link to different radio profiles on a per AP basis.

IMPORTANT!!!   Create new radio profiles for this. Manipulating an existing profile can effect the AP-groups that are using it.

------------------------------
Dustin Burns

Lead Mobility Engineer @Worldcom Exchange, Inc.

ACCX 1271| ACMX 509| ACSP | ACDA | MVP Guru 2022-2023
If my post was useful accept solution and/or give kudos

Original Message:
Sent: May 08, 2023 07:52 AM
From: nkuhl1630
Subject: Adjust RF on an Individual AP

Is there a way to adjust the RF settings for, 2.4 and 5, on an individual AP without affecting those same settings on an entire AP group? We have a few APs that we'd like to keep in the same AP group but need higher RF settings.

Thank you.

------------------------------
Nathan K
------------------------------