Are you triying to setup the convert-aos-ap on the 635 against the VRRP Address or the physical Address of the VRRP Master? I assume this is a standalone environment without any Mobility Conductor, right?
Original Message:
Sent: May 31, 2023 10:15 PM
From: DongF
Subject: AP-635 cannot find its controller (7005)
Original Message:
Sent: May 31, 2023 03:22 AM
From: ariyap
Subject: AP-635 cannot find its controller (7005)
is arm64emmc.ari file on the flash of the 7005?
do a "dir flash" on 7005.
------------------------------
If my post was useful accept solution and/or give kudos.
Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.
Original Message:
Sent: May 31, 2023 02:10 AM
From: DongF
Subject: AP-635 cannot find its controller (7005)
I have try that,but not work.got same error
Original Message:
Sent: May 30, 2023 11:46 PM
From: ariyap
Subject: AP-635 cannot find its controller (7005)
see if you get it to work when you factory default the AP-635.
------------------------------
If my post was useful accept solution and/or give kudos.
Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.
Original Message:
Sent: May 30, 2023 09:00 PM
From: DongF
Subject: AP-635 cannot find its controller (7005)
7005 controller software version is ArubaOS_70xx_8.10.0.6_86193
Original Message:
Sent: May 30, 2023 08:32 PM
From: ariyap
Subject: AP-635 cannot find its controller (7005)
what version of firmware are you running on 7005 controller?
------------------------------
If my post was useful accept solution and/or give kudos.
Any opinions expressed here are solely my own and not necessarily that of HPE or Aruba.
Original Message:
Sent: May 30, 2023 05:59 AM
From: DongF
Subject: AP-635 cannot find its controller (7005)
Hello
I have one 7005 controller which is correctly configured, and a new AP-635. I connected the two devices to the same IPv4 network. However the controller cannot discover the AP.
When I logged into the AP's WebGUI and tried to download by manully typing the controller's IPv4 address. It still failed, I got this error:
Maintenance
Debug
Convert to CAP
=== end of convert log ===
show vpn status
profile name:default
--------------------------------------------------
current using tunnel :unselected tunnel
current tunnel using time :0
ipsec is preempt status :disable
ipsec is fast failover status :disable
ipsec hold on period :600s
ipsec tunnel monitor frequency (seconds/packet) :5
ipsec tunnel monitor timeout by lost packet cnt :6
ipsec reconnect duration (seconds) :30
ipsec primary tunnel crypto type :Cert
ipsec primary tunnel peer address :N/A
ipsec primary tunnel peer tunnel ip :N/A
ipsec primary tunnel ap tunnel ip :N/A
ipsec primary tunnel using interface :N/A
ipsec primary tunnel using MTU :N/A
ipsec primary tunnel current sm status :Init
ipsec primary tunnel tunnel status :Down
ipsec primary tunnel tunnel retry times :0
ipsec primary tunnel tunnel uptime :0
ipsec backup tunnel crypto type :Cert
ipsec backup tunnel peer address :N/A
ipsec backup tunnel peer tunnel ip :N/A
ipsec backup tunnel ap tunnel ip :N/A
ipsec backup tunnel using interface :N/A
ipsec backup tunnel using MTU :N/A
ipsec backup tunnel current sm status :Init
ipsec backup tunnel tunnel status :Down
ipsec backup tunnel tunnel retry times :0
ipsec backup tunnel tunnel uptime :0
end of show vpn status
========================================================
show log upgrade
----------Download log start----------
Executing ('/usr/sbin/wget -T 20 -t 1 -M 41943040 --no-proxy --proxy-passwd=****** --header="X-Ap-Info:CNM1KYJ0DG,cc:88:c7:cc:11:e4,AP-635" -a /tmp/download_url_log ftp://sap:x@192.168.3.6/arm64emmc.ari')
fetching ('/usr/sbin/wget -T 20 -t 1 -M 41943040 --no-proxy --proxy-passwd=****** --header="X-Ap-Info:CNM1KYJ0DG,cc:88:c7:cc:11:e4,AP-635" -a /tmp/download_url_log ftp://sap:x@192.168.3.6/arm64emmc.ari')
--07:54:05-- ftp://sap:*password*@192.168.3.6/arm64emmc.ari
=> `arm64emmc.ari'
Connecting to 192.168.3.6:21... connected.
Logging in as sap ... Logged in!
==> SYST ... done. ==> PWD ... done.
==> TYPE I ... done. ==> CWD not needed.
==> PASV ... done. ==> RETR arm64emmc.ari ...
No such file `arm64emmc.ari'.
Error: failed to retrieve image
Info: try with tftp to download the image.
Error: failed again to retrieve image with tftp proto
cleaning up
Thank you a million if anyone can help!!