I have one 7005 controller which is correctly configured, and a new AP-635. I connected the two devices to the same IPv4 network. However the controller cannot discover the AP.
When I logged into the AP's WebGUI and tried to download by manully typing the controller's IPv4 address. It still failed, I got this error:
MaintenanceDebugConvert to CAP
=== end of convert log ===show vpn status
profile name:default--------------------------------------------------current using tunnel :unselected tunnelcurrent tunnel using time :0ipsec is preempt status :disableipsec is fast failover status :disableipsec hold on period :600sipsec tunnel monitor frequency (seconds/packet) :5ipsec tunnel monitor timeout by lost packet cnt :6ipsec reconnect duration (seconds) :30
ipsec primary tunnel crypto type :Certipsec primary tunnel peer address :N/Aipsec primary tunnel peer tunnel ip :N/Aipsec primary tunnel ap tunnel ip :N/Aipsec primary tunnel using interface :N/Aipsec primary tunnel using MTU :N/Aipsec primary tunnel current sm status :Initipsec primary tunnel tunnel status :Downipsec primary tunnel tunnel retry times :0ipsec primary tunnel tunnel uptime :0
ipsec backup tunnel crypto type :Certipsec backup tunnel peer address :N/Aipsec backup tunnel peer tunnel ip :N/Aipsec backup tunnel ap tunnel ip :N/Aipsec backup tunnel using interface :N/Aipsec backup tunnel using MTU :N/Aipsec backup tunnel current sm status :Initipsec backup tunnel tunnel status :Downipsec backup tunnel tunnel retry times :0ipsec backup tunnel tunnel uptime :0end of show vpn status========================================================
show log upgrade----------Download log start----------
Executing ('/usr/sbin/wget -T 20 -t 1 -M 41943040 --no-proxy --proxy-passwd=****** --header="X-Ap-Info:CNM1KYJ0DG,cc:88:c7:cc:11:e4,AP-635" -a /tmp/download_url_log ftp://sap:email@example.com/arm64emmc.ari')fetching ('/usr/sbin/wget -T 20 -t 1 -M 41943040 --no-proxy --proxy-passwd=****** --header="X-Ap-Info:CNM1KYJ0DG,cc:88:c7:cc:11:e4,AP-635" -a /tmp/download_url_log ftp://sap:firstname.lastname@example.org/arm64emmc.ari')--07:54:05-- ftp://sap:*email@example.com/arm64emmc.ari => `arm64emmc.ari'Connecting to 192.168.3.6:21... connected.Logging in as sap ... Logged in!==> SYST ... done. ==> PWD ... done.==> TYPE I ... done. ==> CWD not needed.==> PASV ... done. ==> RETR arm64emmc.ari ... No such file `arm64emmc.ari'.
Error: failed to retrieve imageInfo: try with tftp to download the image.Error: failed again to retrieve image with tftp protocleaning up
Thank you a million if anyone can help!!
what version of firmware are you running on 7005 controller?
7005 controller software version is ArubaOS_70xx_22.214.171.124_86193
see if you get it to work when you factory default the AP-635.
I have try that,but not work.got same error
is arm64emmc.ari file on the flash of the 7005?do a "dir flash" on 7005.
Can you give more information on how the APs are discovering the Controller?By DHCP Options, DNS or L2 Discovery?
Can you please give an output of "show version" of the Controller
Are you triying to setup the convert-aos-ap on the 635 against the VRRP Address or the physical Address of the VRRP Master? I assume this is a standalone environment without any Mobility Conductor, right?
For L3, either use DHCP option 43 (Vendor Spesific Info), or DNS host record aruba-conductor (from 126.96.36.199), and aruba-master to locate the controller, and FTP (default) or TFTP at the controller.
However default L2 mechanism is ADP (Aruba Discovery Protocol) ADP is enabled by default on all Aruba APs and managed devices. With ADP, APs send out periodic multicast and broadcast queries to locate the Mobility Conductor.(Check if running : show adp config, if not run: adp discovery enable and adp igmp-join enable.)
© Copyright 2023 Hewlett Packard Enterprise Development LPAll Rights Reserved.