Aruba Central

Hello,

I have three AOS-CX 6100 switches and the are In sync in the default group.

When I want to move them to my group, where my 41 AP-515 are in, the switches give the config status "not in sync".

How can I get the switches in that group with the config status in sync ?

Second question can I move the DHCP from VLAN 1 to another VLAN ?

Regards,

Bart Engelen

There is likely a configuration held on the Default Group context that is missing from your destination group. 

You would want to make sure those Groups have a mirrored configuration for critical components. 

Or when you move the device, you could test retaining the original configuration - see below.

You maybe able to see the the Sync Issue or Local Overrides by navigating to: the specific device > Device > Config > Configuration Status

Hello,

I have three AOS-CX 6100 switches and the are In sync in the default group.

When I want to move them to my group, where my 41 AP-515 are in, the switches give the config status "not in sync".

How can I get the switches in that group with the config status in sync ?

Second question can I move the DHCP from VLAN 1 to another VLAN ?

Regards,

Bart Engelen

Hello,

Thanks for your answer.

I got this in the configuration status page, on all three devices.

There is likely a configuration held on the Default Group context that is missing from your destination group. 

You would want to make sure those Groups have a mirrored configuration for critical components. 

Or when you move the device, you could test retaining the original configuration - see below.

You maybe able to see the the Sync Issue or Local Overrides by navigating to: the specific device > Device > Config > Configuration Status

Hello,

I have three AOS-CX 6100 switches and the are In sync in the default group.

When I want to move them to my group, where my 41 AP-515 are in, the switches give the config status "not in sync".

How can I get the switches in that group with the config status in sync ?

Second question can I move the DHCP from VLAN 1 to another VLAN ?

Regards,

Bart Engelen

You would now need to explore what "Pending Changes" are not sync'd. As well as what "Local Overrides" are still applied to the switch. 

At that point you can decide to eliminate those local overrides or add them to your destination group configuration. 

Hello,

Thanks for your answer.

I got this in the configuration status page, on all three devices.

There is likely a configuration held on the Default Group context that is missing from your destination group. 

You would want to make sure those Groups have a mirrored configuration for critical components. 

Or when you move the device, you could test retaining the original configuration - see below.

You maybe able to see the the Sync Issue or Local Overrides by navigating to: the specific device > Device > Config > Configuration Status

Hello,

I have three AOS-CX 6100 switches and the are In sync in the default group.

When I want to move them to my group, where my 41 AP-515 are in, the switches give the config status "not in sync".

How can I get the switches in that group with the config status in sync ?

Second question can I move the DHCP from VLAN 1 to another VLAN ?

Regards,

Bart Engelen

I am very new to Aruba Central.

How can I explore the what "Pending Changes" ?

I see the local Overrides but the settings in Aruba Central are correct and working on my switches.

How can I get ride of this overrides?

You would now need to explore what "Pending Changes" are not sync'd. As well as what "Local Overrides" are still applied to the switch. 

At that point you can decide to eliminate those local overrides or add them to your destination group configuration. 

Hello,

Thanks for your answer.

I got this in the configuration status page, on all three devices.

There is likely a configuration held on the Default Group context that is missing from your destination group. 

You would want to make sure those Groups have a mirrored configuration for critical components. 

Or when you move the device, you could test retaining the original configuration - see below.

You maybe able to see the the Sync Issue or Local Overrides by navigating to: the specific device > Device > Config > Configuration Status

Hello,

I have three AOS-CX 6100 switches and the are In sync in the default group.

When I want to move them to my group, where my 41 AP-515 are in, the switches give the config status "not in sync".

How can I get the switches in that group with the config status in sync ?

Second question can I move the DHCP from VLAN 1 to another VLAN ?

Regards,

Bart Engelen