Wireless Access

 View Only
Back to discussions
Expand all | Collapse all

How can I know if the AP I am looking for is the right one among the numerous APs??

This thread has been viewed 19 times

  • 1.  How can I know if the AP I am looking for is the right one among the numerous APs??

    Posted Nov 30, 2022 08:55 AM
    I need to set up hundreds of APs.

    I'm trying to make the switch a DHCP server and join dozens of APs to the controller through it.

    And I will change the settings of the AP in the controller.
    For example AP01, AP02, AP03 ....

    How do I find AP01 after that??

    The way I can think of is to turn off the power of the AP and find the AP whose LED is off.

    Any ideas better than this??


  • 2.  RE: How can I know if the AP I am looking for is the right one among the numerous APs??

    Posted Nov 30, 2022 04:43 PM
    generally you would name the APs based on their location in a map, that way you can keep track of them.
    you can also change LED on/off a specific APs, using LED operating mode in AP system profile
    https://www.arubanetworks.com/techdocs/ArubaOS_8.9.0_Web_Help/Content/arubaos-solutions/access-points/conf-ap-syst-prof.htm


    ------------------------------
    Any opinions expressed here are solely my own and not necessarily that of Hewlett Packard Enterprise or Aruba.
    ------------------------------

    Original Message


  • 3.  RE: How can I know if the AP I am looking for is the right one among the numerous APs??
    Best Answer

    Posted Dec 01, 2022 09:05 AM
    From the controller you can make the LEDs blink on one or more of your APs:
    (md7005) *#ap-leds
all                     Control LEDs on all APs
ap-group                Control LEDs on APs in this group
ap-name                 Control LEDs on AP with this name
ip-addr                 Control LEDs on AP at this IP address
wired-mac               Control LEDs on AP at this MAC address

(md7005) *#ap-leds ap-name
<ap-name>               Control LEDs on AP with this name

(md7005) *#ap-leds ap-name NLPD-AP325-01
blink                   Make LEDs blink for identification
fault-disable           Disable the fault LED if fault is detected. One LED APs
                        only, e.g.,
                        AP-228/AP-27x/AP-318/AP-36x/AP-37x/AP-387/AP-518/AP-56x/
                        AP-57x.
fault-enable            Enable the fault LED if fault is detected. One LED APs
                        only, e.g.,
                        AP-228/AP-27x/AP-318/AP-36x/AP-37x/AP-387/AP-518/AP-56x/
                        AP-57x.
normal                  Restore LEDs to their normal behavior

(md7005) *#ap-leds ap-name NLPD-AP325-01 blink
<cr>
(md7005) *#ap-leds ap-name NLPD-AP325-01 normal
<cr>​

    As you can see, you can also blink on AP group or by IP or by MAC address.



    ------------------------------
    Herman Robers
    ------------------------
    If you have urgent issues, always contact your Aruba partner, distributor, or Aruba TAC Support. Check https://www.arubanetworks.com/support-services/contact-support/ for how to contact Aruba TAC. Any opinions expressed here are solely my own and not necessarily that of Hewlett Packard Enterprise or Aruba Networks.

    In case your problem is solved, please invest the time to post a follow-up with the information on how you solved it. Others can benefit from that.
    ------------------------------

    Original Message


Related Content