Network Management

 View Only
last person joined: 4 hours ago 

Keep an informative eye on your network with HPE Aruba Networking network management solutions
Expand all | Collapse all

re: HP5920 error

This thread has been viewed 0 times
  • 1.  re: HP5920 error

    Posted Sep 08, 2021 03:21 PM

    good day,

    need assistance with this warning message: The instance "[interface:Bridge-Aggregation12]" of "performance task" "Interface Transmitting Rate" is back to normal for threshold 2, current value is "96.263Mbps".

     

    thanks,

     

    David

     

     


    #imc


  • 2.  RE: re: HP5920 error

    Posted Sep 08, 2021 03:22 PM

    display link-aggregation member-port Ten-GigabitEthernet 1/0/11
    Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,
    D -- Synchronization, E -- Collecting, F -- Distributing,
    G -- Defaulted, H -- Expired

    Ten-GigabitEthernet1/0/11:
    Aggregate Interface: Bridge-Aggregation11
    Local:
    Port Number: 11
    Port Priority: 32768
    Oper-Key: 11
    Flag: {ACDEF}
    Remote:
    System ID: 0x1000, 509a-4ce7-78f0
    Port Number: 34
    Port Priority: 32768
    Oper-Key: 101
    Flag: {ACDEF}
    Received LACP Packets: 1551136 packet(s)
    Illegal: 0 packet(s)
    Sent LACP Packets: 1552134 packet(s)

    >display transceiver diagnosis interface t 1/0/11
    Ten-GigabitEthernet1/0/11 transceiver diagnostic information:
    Current diagnostic parameters:
    Temp.(▒▒C) Voltage(V) Bias(mA) RX power(dBm) TX power(dBm)
    30 3.31 7.19 -2.15 -1.88
    Alarm thresholds:
    Temp.(▒▒C) Voltage(V) Bias(mA) RX power(dBm) TX power(dBm)
    High 73 3.80 13.20 1.00 0.00
    Low -3 2.81 1.00 -9.50 -10.30

    >display transceiver alarm interface t 1/0/11
    Ten-GigabitEthernet1/0/11 transceiver current alarm information:
    None

    display transceiver interface t 1/0/11
    Ten-GigabitEthernet1/0/11 transceiver information:
    Transceiver Type : 10G_BASE_SR_SFP
    Connector Type : LC
    Wavelength(nm) : 850
    Transfer Distance(m) : 80(OM2),20(OM1),300(OM3)
    Digital Diagnostic Monitoring : YES
    Vendor Name : HPE
    Ordering Name : JD092B



  • 3.  RE: re: HP5920 error

    EMPLOYEE
    Posted Sep 08, 2021 04:56 PM

    Hello @dlhall68 ,

    .You need to recheck the threshold into imc interface transmitting rate for threshold 2.

    By default value is set to 100mbps however interface supports 10g.

    You need to recheck the threshold into imc interface transmitting rate for threshold 2.

    By default value is set to 100mbps however interface supports 10g.

    Go to  Resource-->Performance Management-->Global Index Settings  

    Select 'Interface Transmitting Rate' and modify the Threshold 2.

     

    imc_threshold.JPG

     

    Thanks!