Aruba-2930F-48G-PoEP-4SFP# conf t
Aruba-2930F-48G-PoEP-4SFP(config)# vlan 10
Aruba-2930F-48G-PoEP-4SFP(vlan-10)# vlan 20
Aruba-2930F-48G-PoEP-4SFP(vlan-20)# vlan 30
Aruba-2930F-48G-PoEP-4SFP(vlan-30)# vlan 40
Aruba-2930F-48G-PoEP-4SFP(vlan-40)# vlan 50
Aruba-2930F-48G-PoEP-4SFP(vlan-50)# exit
Aruba-2930F-48G-PoEP-4SFP(config)# mirror 1 port 24
Aruba-2930F-48G-PoEP-4SFP(config)# vlan 10
Aruba-2930F-48G-PoEP-4SFP(vlan-10)# monitor all both mirror 1
Aruba-2930F-48G-PoEP-4SFP(vlan-10)# vlan 20
Aruba-2930F-48G-PoEP-4SFP(vlan-20)# monitor all both mirror 1
Aruba-2930F-48G-PoEP-4SFP(vlan-20)# vlan 30
Aruba-2930F-48G-PoEP-4SFP(vlan-30)# monitor all both mirror 1
Aruba-2930F-48G-PoEP-4SFP(vlan-30)# vlan 40
Aruba-2930F-48G-PoEP-4SFP(vlan-40)# monitor all both mirror 1
Aruba-2930F-48G-PoEP-4SFP(vlan-40)# exit
Aruba-2930F-48G-PoEP-4SFP(config)# exit
Aruba-2930F-48G-PoEP-4SFP# show monitor
There are no Remote Mirroring endpoints currently assigned.
Network Monitoring
Sessions Status Type Sources Mirror-Policy
-------- ----------------- ----- ------- -------------
1 active port 1 No
2 not defined
3 not defined
4 not defined
Aruba-2930F-48G-PoEP-4SFP# show monitor 1
Network Monitoring
Session: 1 Session Name:
Mirror Destination: 24 (Port)
Monitoring Sources Direction Truncation Mirror Policy
------------------ --------- ---------- -------------
VLAN: 40 Both No -
Aruba-2930F-48G-PoEP-4SFP# conf t
Aruba-2930F-48G-PoEP-4SFP(config)# vlan 50
Aruba-2930F-48G-PoEP-4SFP(vlan-50)# monitor all both mirror 1
Aruba-2930F-48G-PoEP-4SFP(vlan-50)# exit
Aruba-2930F-48G-PoEP-4SFP(config)# exit
Aruba-2930F-48G-PoEP-4SFP# show monitor 1
Network Monitoring
Session: 1 Session Name:
Mirror Destination: 24 (Port)
Monitoring Sources Direction Truncation Mirror Policy
------------------ --------- ---------- -------------
VLAN: 50 Both No -
Aruba-2930F-48G-PoEP-4SFP#
------------------------------
Steve
------------------------------
Original Message:
Sent: Mar 20, 2018 06:09 AM
From: Dobias van Ingen
Subject: Port Mirroring Limit on 5412R and 3810M
Hi Philip,
If you just want to monitor all traffic on these VLANS and have local mirror (exit) port you can simply use these commands without all the classifications.
Let's say VLAN 10 and 20 you need to monitor and port 24 on the switch is the port where all the traffic is send to.
- Configure mirror session (exit):
mirror 1 port 24
- Configure monitor on VLANs
vlan 10
monitor all both mirror 1
vlan 20
monitor all both mirror 1
If I'm correct then this is it. You're done and ready to start monitoring traffic. Be aware when you monitor complete VLAN's that are really busy or have lots of ports on the same switch and send all of this traffic to one port you can potentially overload the mirror port.
Regards, Dobias