Hello,
As advised, I've connected the AP onto our WLAN network prior to deployment and it picked up an image. I have then manually changed the settings of the AP to the remote site and setup the IP, GW, master manually.
I'm on site now and the AP can ping the master controller through the VPN. However, ii'm still not getting the 4 lights up and is not advertising the SSID that I set up in the office.
I had a look at the output and noticed that it's changed its IP from the manually setup one of 192.168.x.x
I can also see that it's using ADP to access the master controller.
Can you please have a look at the output and advise if I've missed something or done something wrong you don't mind?
~ #
APBoot 1.4.0.5 (build 38142)
Built: 2013-04-21 at 22:03:44
Model: AP-11x
CPU: QCA9550 revision: 1.0
Clock: 720 MHz, DDR rate: 600 MHz, Bus clock: 200 MHz
DRAM: 256 MB
POST1: passed
Copy: done
Flash: 32 MB
Power: 802.3af POE
PCI: scanning bus 0 ...
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 168c 0033 00002 01 00000004 00000000 00000000 00000000
Net: eth0
Radio: ar9590#0, qca9550#1
Hit <Enter> to stop autoboot: 0
apboot> printenv
bootdelay=2
baudrate=9600
autoload=n
boardname=Ardbeg
bootcmd=boot ap
autostart=yes
bootfile=mips32.ari
ethaddr=18:64:72:c1:2c:0a
num_ipsec_retry=85
name=Pembroke-VPN-Test
group=Pembroke-House
ip6prefix=64
servername=aruba-master
a_antenna=0
g_antenna=0
usb_type=0
uplink_vlan=0
auto_prov_id=0
is_rmp_enable=0
priority_ethernet=0
priority_cellular=0
cellular_nw_preference=1
usb_power_mode=0
cert_cap=0
mesh_role=0
installation=0
mesh_sae=0
ethact=eth0
ip=192.168.x.x
netmask=255.255.255.0
gateway=192.168.x.x
master=10.181.x.x
start_type=warm_start
stdin=serial
stdout=serial
stderr=serial
Environment size: 595/65532 bytes
apboot> boot
Checking image @ 0xbf100000 (bank 1)
Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
ELF file is 32 bit
Loading .text @ 0x80e00000 (4705672 bytes)
Loading .data @ 0x8127cd90 (32 bytes)
Clearing .bss @ 0x8127cdb0 (16 bytes)
## Starting application at 0x80e00000 ...
Uncompressing............................................
Aruba Networks
ArubaOS Version 6.3.1.3 (build 42233 / label #42233)
Built by p4build@port-royal on 2014-02-11 at 11:29:58 PST (gcc version 4.3.3)
CPU Rev: 1130
955x CPU
flash_size passed from bootloader = 32
arg 1: mem=256M
Flash variant: default
cpu apb ddr apb ath_955x_sys_frequency: cpu 720 ddr 600 ahb 200
Cache parity protection disabled
ath_timer_init: plat time init done
Using 360.000 MHz high precision timer. cycles_per_jiffy=720000
Memory: 251648k/262144k available (1931k kernel code, 10368k reserved, 752k data, 3832k init, 0k highmem)
available.
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=8388608,origSize=17670656
LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com> ..............................................................................................................................................................................................................................................................................
qca955x_pcibios_init: bus 0
qca955x_pcibios_init(1239): PCI 0 CMD write: 0x356
qca955x_pcibios_init: bus 1
qca955x_pcibios_map_irq: IRQ 75 for bus 0
ATH GPIOC major 0
wdt: registered with refresh
Enabling Watchdog
Talisker RSSI LED initialization
Concatenating MTD devices:
(0): "bank1"
(1): "bank2"
into device "flash"
Creating 1 MTD partitions on "flash":
0x00000000-0x02000000 : "flash"
i2c /dev entries driver
i2c-talisker: using default base 0x18040000
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
Starting Kernel DES KAT ...Completed Kernel DES KAT
Starting Kernel AES KAT ...Completed Kernel AES KAT
Starting Kernel AESGCM KAT ...Completed Kernel AESGCM KAT
Domain Name: arubanetworks.com
No panic info available
qca955x_GMAC: Length per segment 1536
955x_GMAC: qca955x_gmac_attach
955x_GMAC: qca955x_set_gmac_caps
Currently in polling mode unit0
mac:0 Registering S17....
qca955x_GMAC: RX TASKLET - Pkts per Intr:100
qca955x_GMAC: Mac address for unit 0:8078ebc0
qca955x_GMAC: 18:64:72:c1:2c:0a
qca955x_GMAC: Max segments per packet : 1
qca955x_GMAC: Max tx descriptor count : 128
qca955x_GMAC: Max rx descriptor count : 2048
qca955x_GMAC: Mac capability flags : 2201
_athrs17_mac0_intf done
athrs17_reg_init:done
Phy setup Complete
drvlog_mod: module license 'Proprietary' taints kernel.
AP xml model 72, num_radios 2 (jiffies 3486)
init_asap_mod: installation:0
radio 0: band 1 ant 0 max_ssid 16
radio 1: band 0 ant 0 max_ssid 16
Starting watchdog process...
Getting an IP address...
To set s17 LOOKUP_CTRL_REG registers, flag 0
athr_gmac_ring_alloc Allocated 2048 at 0x80648000
athr_gmac_ring_alloc Allocated 32768 at 0x807d0000
955x_GMAC: eth0 in RGMII MODE
Scorpion -----> S17 PHY
FINAL XMII VAL after RX Calibration - 0x84000101
Error: cannot be initialized twice!
athrs17_reg_init:done
Setting PHY...
Phy setup Complete
To set s17 LOOKUP_CTRL_REG registers, flag 1
ADDRCONF(NETDEV_UP): bond0: link is not ready
Enet:0 port0 up
eth0 RGMII 100Mbps full duplex
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
192.168.x.x 255.255.255.0 192.168.x.x
Running ADP...Done. Master is 10.181.x.x
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_rate_atheros: Aruba Networks Rate Control Algorithm
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_spectrum: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_pci: 0.9.4.5 (Atheros/multi-bss)
Restoring Cal data from Flash
Reading from Addr: 0xbffe5000
ath_attach: scn 8dd60280 sc 8dd80000 ah 8ddc0000
wifi0: Base BSSID 18:64:72:92:c0:b0, 16 available BSSID(s)
bond0 address=18:64:72:c1:2c:0a
br0 address=18:64:72:c1:2c:0a
wifi0: AP type AP-115, radio 0, max_bssids 16
wifi0: Atheros 9580: mem=0x10000000, irq=75 hw_base=0xb0000000
ath_ahb: 0.9.4.5 (Atheros/multi-bss)
ath_ahb: init_ath_wmac
Enterprise mode: 0x30000000
Restoring Cal data from Flash
Reading from Addr: 0xbffe1000
ath_attach: scn 8d860280 sc 8d880000 ah 8d8c0000
wifi1: Base BSSID 18:64:72:92:c0:a0, 16 available BSSID(s)
bond0 address=18:64:72:c1:2c:0a
br0 address=18:64:72:c1:2c:0a
wifi1: AP type AP-115, radio 1, max_bssids 16
wifi1: Atheros 955x: mem=0xb8100000, irq=2
shutting down watchdog process (nanny will restart it)...
<<<<< Welcome to the Access Point >>>>>