Wireless Access

last person joined: yesterday 

Access network design for branch, remote, outdoor, and campus locations with HPE Aruba Networking access points and mobility controllers.
Back to discussions
Expand all | Collapse all

AP does not take IP address

This thread has been viewed 1 times

  • 1.  AP does not take IP address

    Posted Dec 15, 2011 02:24 AM

    AP does not take IP address

    When I connect the faulty AP to my Laptop through console cable I get the following

    

    Hit <Enter> to stop autoboot:  0

    apboot>

    apboot> 

    apboot> dhcp

    en0:    Down   1Gbs Half duplex, (port  1)

    BOOTP broadcast 1

    BOOTP broadcast 2

    BOOTP broadcast 3

    BOOTP broadcast 4

    BOOTP broadcast 5

    Retry count exceeded; starting again

    en1:    Down   1Gbs Half duplex, (port  0)

    BOOTP broadcast 1

    en1: Down   1Gbs Full duplex, (port  0)

    en1: Up     1Gbs Full duplex, (port  0)

    en1: Down   1Gbs Half duplex, (port  0)

    BOOTP broadcast 2

    en1: Down   1Gbs Full duplex, (port  0)

    en1: Up     1Gbs Full duplex, (port  0)

    en1: Down   1Gbs Half duplex, (port  0)

    BOOTP broadcast 3

    en1: Down   1Gbs Full duplex, (port  0)

    en1: Up     1Gbs Full duplex, (port  0)

     BOOTP broadcast 4

    en1: Down   1Gbs Half duplex, (port  0)

    BOOTP broadcast 5

    en1: Down   1Gbs Full duplex, (port  0)

    en1: Up     1Gbs Full duplex, (port  0)

    en1: Down   1Gbs Half duplex, (port  0)

    Retry count exceeded; starting again

    en0: Down  10Mbs Half duplex, (port  1)

    BOOTP broadcast 1

    en0: Down   1Gbs Half duplex, (port  1)

    BOOTP broadcast 2

    BOOTP broadcast 3

    BOOTP broadcast 4

    BOOTP broadcast 5

     

    in case of autoboot i got the following error

     

    eth1: Link down secure_jack_link_state_change: Error finding device eth1

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

     bonding: bond0: link status definitely down for interface eth1, disabling it bonding: bond0: now running without any active interface ! PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

     PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

     PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    eth1:   1Gbs Full duplex, port  0, queue  0

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    eth1: Link down

    secure_jack_link_state_change: Error finding device eth1

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

     PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

     PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

     PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

     PCI ERROR[MR_WABT]: PCI master abort detected on write.

     PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    PCI ERROR[MR_WABT]: PCI master abort detected on write.

    eth1:   1Gbs Full duplex, port  0, queue  0

    eth1: Link down

     

     



  • 2.  RE: AP does not take IP address

    EMPLOYEE
    Posted Dec 15, 2011 06:11 AM

    What version of ArubaOS Code is this and What AP Model?

     



  • 3.  RE: AP does not take IP address

    Posted Dec 15, 2011 03:05 PM

    AP 125

    I'm not sure about OS version, i'm not in my office to check it.

    i've tried to assign static IP address and default getaway, it was OK and I was able to save the configuration

    but the interface go's up and down, so I could not ping my controller or even getaway



  • 4.  RE: AP does not take IP address

    EMPLOYEE
    Posted Dec 15, 2011 03:06 PM

    You should open a support case based on that output.