Wireless Access

Reply
Highlighted
Occasional Contributor I

AP305 Cannot See in Airwave

I have an existing controller 7010 and some access points 103 with version 6.5.1.9 and use airwave with version 8.2.4, after I changed the ap to 305 the ap was not on the "list" automatically, I tried to input manually but an error occurred snmp failed, what should I do? does the airwave version not support AP?


Accepted Solutions
Highlighted
Occasional Contributor I

Re: AP305 Cannot See in Airwave

hello all this problem solve after being remote by TAC,The problem is that the RAM memory is full, so Airwave can't make new searches for access points,The solution is to clear the cache that is not in use and have to upgrade RAM and CPU

 

thanks all

View solution in original post


All Replies
Highlighted
Guru Elite

Re: AP305 Cannot See in Airwave

If the new AP shows up on the controller, it show up in Airwave.  If Airwave does not have a rule to automatically add the device into airwave, it should show up under the "new" device counter at the top.


*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.5 User Guide
InstantOS 8.5 User Guide
Airheads Knowledgebase
Airheads Learning Videos
Remote Access Point Solution Guide
ArubaOS Consolidated Release Notes
ArubaOS 8 ViA VPN Solution Guide
Highlighted

Re: AP305 Cannot See in Airwave

AP 305 should be supported on 8.2.4, same is mentioned in the supported device guide for 8.2.4.

We cannot add a thin AP manually to Airwave using SNMP, Airwave polls the Controller and gets the AP info.

 

  • Is this AP showing up on controller?
  • Could we try to poll the controller on Airwave once? Do we see any error while polling?
  • After polling could we double check the new devices list again?

Also, once the AP shows up you would have to do replace hardware if we still have the old 105 on Airwave so that historical data for the device wont be lost.

 

Regards,
Vishnu
If my post helped you, don't forget to give kudos ;)
Highlighted
Occasional Contributor I

Re: AP305 Cannot See in Airwave

true, but the P305 apep5 will not appear on airwave and I have tried adding the manual but the error will appear, any other suggestions?

Highlighted
Occasional Contributor I

Re: AP305 Cannot See in Airwave

I have done a poll on the controller so that new devices that are in the controller appear, but it does not appear at all for the new AP, do I have to restart the airwave?

Highlighted

Re: AP305 Cannot See in Airwave

Could we try restarting the daemon on the server once from ampcli? That should re initiate any process which are stuck.
Also, i would suggest moving to latter code as 8.2.4 is too old code.

 

Regards,
Vishnu
If my post helped you, don't forget to give kudos ;)
Highlighted
Occasional Contributor I

Re: AP305 Cannot See in Airwave

we can't restart, because this airwave is connected from many controllers in various cities, is it affected by all data?

Highlighted
Guru Elite

Re: AP305 Cannot See in Airwave

Did you try to search for the access point in Airwave using its  ip address or  wired Mac address?


*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.5 User Guide
InstantOS 8.5 User Guide
Airheads Knowledgebase
Airheads Learning Videos
Remote Access Point Solution Guide
ArubaOS Consolidated Release Notes
ArubaOS 8 ViA VPN Solution Guide
Highlighted
Occasional Contributor I

Re: AP305 Cannot See in Airwave

I have tried manually by entering the device name and IP address of the device, after waiting a few minutes the AP remained down and the status failed SNMP,see my attachments

Highlighted
Moderator

Re: AP305 Cannot See in Airwave

Airwave is not meant to interact with the IP of the AP, it talks the controller only. Get the AP up on the controller, then wait for Airwave to poll the controller.

Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: