My AP stuck in a boot loop.
Please help me. Thank you!
APBoot 1.5.3.4 (build 43264)
Built: 2014-04-16 at 15:38:45
Model: AP-22x
CPU0: P1020E, Version: 1.1, (0x80ec0011)
Core: E500, Version: 5.1, (0x80212051)
Clock:
CPU0: 800 MHz
CPU1: 800 MHz
CCB: 400 MHz
DDR: 333.333 MHz (666.667 MT/s data rate) (Asynchronous)
LBC: 25 MHz
L1: D-cache 32KB enabled
I-cache 32KB enabled
I2C: ready
DRAM: Configuring DDR for 666.667 MT/s data rate
DDR: 512 MB (DDR3, 32-bit, CL=5, ECC off)
POST1: memory passed
Flash: 32 MB
L2: 256 KB enabled
Power: DC
PCIe1: RC, link up, x1
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 14e4 43a2 00002 03 80000004 00000000 80200004 00000000
PCIe2: RC, link up, x1
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 14e4 43a1 00002 03 a0000004 00000000 a0200004 00000000
Net: eth0, eth1
Radio: bcm43460#0, bcm43460#1
Hit <Enter> to stop autoboot: 0
Checking image @ 0xee000000
Invalid image format version: 0xffffffff
Checking image @ 0xeee00000
Copying image from 0xeee00000
Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
Aruba Networks
ArubaOS Version 6.3.1.0 (build 39345 / label #39345)
Built by p4build@tortuga on 2013-08-08 at 16:30:24 PDT (gcc version 4.5.1)
Memory: 510348k/524288k available (8348k kernel code, 13940k reserved, 540k data , 352k bss, 5008k init)
Processor 1 found.
Brought up 2 CPUs
PCI: Probing PCI hardware
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0001:02:00.0: PCI bridge to [bus 03-ff]
pci 0000:00:00.0: enabling device (0106 -> 0107)
pci 0001:02:00.0: enabling device (0106 -> 0107)
ee000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
/proc/gfar_eth0_stats created
/proc/gfar_eth1_stats created
Enabling watchdog on CPU 1
Enabling watchdog on CPU 0
Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
Starting Kernel DES KAT ...Completed Kernel DES KAT
Starting Kernel AES KAT ...Completed Kernel AES KAT
Domain Name: arubanetworks.com
No panic info available
Ethernet port 1 mode: active-standby
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): bond0: link is not ready
bonding: bond0: enslaving eth0 as a backup interface with a down link.
ADDRCONF(NETDEV_UP): eth1: link is not ready
bonding: bond0: enslaving eth1 as a backup interface with a down link.
AP xml model 66, num_radios 2 (jiffies 3213)
init_asap_mod: installation:0
radio 0: band 1 ant 0 max_ssid 16
radio 1: band 0 ant 0 max_ssid 16
ethernet_device_event: dev eth0 is up
ASAP Slowpath initialized
Starting watchdog process...
Getting an IP address...
PHY: eth1 (mdio@ffe24000:01) - Link is Up - 1000/Full
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
bonding: bond0: first active interface up!
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
10.10.10.54 255.255.255.0 10.10.10.1
Running ADP...cat: /tmp/master: No such file or directory
Done. Master is
killall: nanny: no process killed
killall: sapd: no process killed
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
Restarting system.
After I manual config DNS, factory_reset, purge enviroment... I got other error
APBoot 1.5.3.4 (build 43264)
Built: 2014-04-16 at 15:38:45
Model: AP-22x
CPU0: P1020E, Version: 1.1, (0x80ec0011)
Core: E500, Version: 5.1, (0x80212051)
Clock:
CPU0: 800 MHz
CPU1: 800 MHz
CCB: 400 MHz
DDR: 333.333 MHz (666.667 MT/s data rate) (Asynchronous)
LBC: 25 MHz
L1: D-cache 32KB enabled
I-cache 32KB enabled
I2C: ready
DRAM: Configuring DDR for 666.667 MT/s data rate
DDR: 512 MB (DDR3, 32-bit, CL=5, ECC off)
POST1: memory passed
Flash: 32 MB
L2: 256 KB enabled
Power: DC
PCIe1: RC, link up, x1
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 14e4 43a2 00002 03 80000004 00000000 80200004 00000000
PCIe2: RC, link up, x1
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 14e4 43a1 00002 03 a0000004 00000000 a0200004 00000000
Net: eth0, eth1
Radio: bcm43460#0, bcm43460#1
Hit <Enter> to stop autoboot: 0
Checking image @ 0xee000000
Invalid image format version: 0xffffffff
Checking image @ 0xeee00000
Copying image from 0xeee00000
Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
Aruba Networks
ArubaOS Version 6.3.1.0 (build 39345 / label #39345)
Built by p4build@tortuga on 2013-08-08 at 16:30:24 PDT (gcc version 4.5.1)
Memory: 510348k/524288k available (8348k kernel code, 13940k reserved, 540k data, 352k bss, 5008k init)
Processor 1 found.
Brought up 2 CPUs
PCI: Probing PCI hardware
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0001:02:00.0: PCI bridge to [bus 03-ff]
pci 0000:00:00.0: enabling device (0106 -> 0107)
pci 0001:02:00.0: enabling device (0106 -> 0107)
ee000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
/proc/gfar_eth0_stats created
/proc/gfar_eth1_stats created
Enabling watchdog on CPU 1
Enabling watchdog on CPU 0
Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
Starting Kernel DES KAT ...Completed Kernel DES KAT
Starting Kernel AES KAT ...Completed Kernel AES KAT
Domain Name: arubanetworks.com
No panic info available
apfcutil: sector CACHE: Cache uninitialized
apfcutil: sector RAP: Cache uninitialized
apfcutil -c RAP: Uninitialized. Initializing.........
apfcutil: sector MESH Prov: Cache uninitialized
Ethernet port 1 mode: active-standby
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): bond0: link is not ready
bonding: bond0: enslaving eth0 as a backup interface with a down link.
ADDRCONF(NETDEV_UP): eth1: link is not ready
bonding: bond0: enslaving eth1 as a backup interface with a down link.
AP xml model 66, num_radios 2 (jiffies 4696)
init_asap_mod: installation:0
radio 0: band 1 ant 0 max_ssid 16
radio 1: band 0 ant 0 max_ssid 16
ethernet_device_event: dev eth0 is up
ASAP Slowpath initialized
Starting watchdog process...
Getting an IP address...
PHY: eth1 (mdio@ffe24000:01) - Link is Up - 1000/Full
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
bonding: bond0: first active interface up!
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
192.168.1.41 255.255.255.0 192.168.1.1
Running ADP...Done. Master is 192.168.1.2
wifi0: AP type AP-225, radio 0, max_bssids 16
wifi1: AP type AP-225, radio 1, max_bssids 16
shutting down watchdog process (nanny will restart it)...
<<<<< Welcome to the Access Point >>>>>
~ #
~ # ?
?: Permission denied
~ # help
help: Permission denied
The system is going down NOW !!
Sending SIGTERM to all processes.
Please stand by while rebooting the system.
Restarting system.
I've tried tftpboot but no luck
Hit <Enter> to stop autoboot: 0
apboot> tftpboot
eth0: link down.
eth1: link up, speed 1 Gb/s, full duplex
DHCP broadcast 1
DHCP IP address: 192.168.1.42
DHCP subnet mask: 255.255.255.0
DHCP def gateway: 192.168.1.1
DHCP DNS server: 192.168.1.1
DHCP DNS domain:
ADP multicast 1
ADP broadcast 1
ADP multicast 2
ADP broadcast 2
ADP multicast 3
Retry count exceeded
DNS request 1 for aruba-master. to 192.168.1.1
Using eth1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.42
Filename 'e500.ari'.
Load address: 0x8000000
Loading: T T T T T
Retry count exceeded; starting again
eth0: link down.
eth1: link up, speed 1 Gb/s, full duplex
DHCP broadcast 1
DHCP IP address: 192.168.1.42
DHCP subnet mask: 255.255.255.0
DHCP def gateway: 192.168.1.1
DHCP DNS server: 192.168.1.1
DHCP DNS domain:
ADP broadcast 3
ADP multicast 4
ADP broadcast 4
ADP multicast 5
ADP broadcast 5
Retry count exceeded
DNS request 1 for aruba-master. to 192.168.1.1
Using eth1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.42
Filename 'e500.ari'.
Load address: 0x8000000
Loading: T T T T T
Retry count exceeded; starting again
eth0: link down.
eth1: link up, speed 1 Gb/s, full duplex
DHCP broadcast 1
DHCP IP address: 192.168.1.42
DHCP subnet mask: 255.255.255.0
DHCP def gateway: 192.168.1.1
DHCP DNS server: 192.168.1.1
DHCP DNS domain:
ADP multicast 6
ADP broadcast 6
ADP multicast 7
ADP broadcast 7
ADP multicast 8
Retry count exceeded
DNS request 1 for aruba-master. to 192.168.1.1
Using eth1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.42
Filename 'e500.ari'.
Load address: 0x8000000
Loading: T T T T T
Retry count exceeded; starting again
eth0: link down.
eth1: link up, speed 1 Gb/s, full duplex