Wireless Access

Reply
Occasional Contributor II

Re: Migrate from A200 controller to A620 controller

see this one now, i have reset the ap and follow same steps as mention before and it was up but i dint provision it yet and took the log

Highlighted
Aruba Employee

Re: Migrate from A200 controller to A620 controller

Its going to AM due to regulatory domain. 

 

AP "d8:c7:c8:cf:5c:ae" Radio 0 Operating Information
----------------------------------------------------
Item             Value    Source
----             -----    ------
High throughput  Enabled  Configuration
Mode             AM       Regulatory
Band             802.11g  Configuration

 please let us know the country code of the controller and the "show ap regulatory-domain-profile default"

 

show ap allowed-channels ap-name d8:c7:c8:cf:5c:ae

 

Vinod Kumaar AVM ACMX, ACDX
Principal Network Engineer
Customer Advocacy | Aruba Networks Inc.

Did something you read in the Community solve a problem for you? If so, click "Accept as Solution" in the bottom right hand corner of the post.
Highlighted
Occasional Contributor II

Re: Migrate from A200 controller to A620 controller

---------------------------

 

show ap allowed-channels ap-name d8:c7:c8:cf:5c:ae

Allowed Channels for AP "d8:c7:c8:cf:5c:ae" Country Code "AE" Country "United Ar
ab Emirates"
--------------------------------------------------------------------------------
------------
PHY Type                 Allowed Channels
--------                 ----------------
802.11g (indoor)         None
802.11a (indoor)         149 153 157 161 165
802.11g (outdoor)        None
802.11a (outdoor)        149 153 157 161 165
802.11g 40MHz (indoor)   None
802.11a 40MHz (indoor)    149-153 157-161
802.11g 40MHz (outdoor)  None
802.11a 40MHz (outdoor)   149-153 157-161
802.11a (DFS)

 

 

 

i selected AE as i am in United Arab Emirates

Highlighted
Aruba Employee

Re: Migrate from A200 controller to A620 controller

Looks like in this code AP-93 is not certified for AE for g band. it should work for 'a' band. however in 6.1.3.6, i see the following 

 

#show version
Aruba Operating System Software.
ArubaOS (MODEL: Aruba3400), Version 6.1.3.6
Website: http://www.arubanetworks.com
Copyright (c) 2002-2012, Aruba Networks, Inc.
Compiled on 2012-12-11 at 12:51:05 PST (build 36470) by p4build

 

#show ap allowed-channels country-code AE ap-type 93

Allowed Channels for AP Type 93 Country Code "AE" Country "United Arab Emirates"
--------------------------------------------------------------------------------
PHY Type Allowed Channels
-------- ----------------
802.11g (indoor) 1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (indoor) 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140
802.11g (outdoor) 1 2 3 4 5 6 7 8 9 10 11 12 13
802.11a (outdoor) 100 104 108 112 116 120 124 128 132 136 140
802.11g 40MHz (indoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11
802.11a 40MHz (indoor) 36-40 44-48 52-56 60-64 100-104 108-112 116-120 124-128 132-136
802.11g 40MHz (outdoor) 1-5 2-6 3-7 4-8 5-9 6-10 7-11
802.11a 40MHz (outdoor) 100-104 108-112 116-120 124-128 132-136
802.11a (DFS) 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140

 

 

Vinod Kumaar AVM ACMX, ACDX
Principal Network Engineer
Customer Advocacy | Aruba Networks Inc.

Did something you read in the Community solve a problem for you? If so, click "Accept as Solution" in the bottom right hand corner of the post.
Highlighted
Occasional Contributor II

Re: Migrate from A200 controller to A620 controller

ok i will disable G band and enable only A band and test it out if it comes back to AP

Highlighted
Occasional Contributor II

Re: Migrate from A200 controller to A620 controller

Thank you vkumaar for guiding me to right way.

 

i have 2 AP working now on A band also it shows me now wireless LAN ssid activated.

 

sorry but one more little help need from you, i cannot see the SSID that i configure and which is activated.

 

i did make sure if it is not set as hide SSID or its disabled in profile configure.

 

Can you guide me through in this as well Please ?

 

 

 

 

 

Highlighted
Occasional Contributor II

Re: Migrate from A200 controller to A620 controller

Can any body help me trouble shooting why the SSID i have configured is not broad casting, the AP status is active now.

 

 

Highlighted
Guru Elite

Re: Migrate from A200 controller to A620 controller

Did you use the LAN/WLAN Wizard?  That is the best way to do that.


*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.5 User Guide
InstantOS 8.5 User Guide
Airheads Knowledgebase
Airheads Learning Videos
Aruba Central Documentation
ArubaOS Consolidated Release Notes
Aruba VIA ASE Solution - Configure VIA VPN
Highlighted
Occasional Contributor II

Re: Migrate from A200 controller to A620 controller

Yup i did the wizard even and create new SSID and applied but still it wont broadcast

Highlighted
Guru Elite

Re: Migrate from A200 controller to A620 controller

In What ap-group did you create the WLAN?  Is the AP in the same ap-group?

 

type "show ap database" and "show ap bss-table"


*Answers and views expressed by me on this forum are my own and not necessarily the position of Aruba Networks or Hewlett Packard Enterprise.*
ArubaOS 8.5 User Guide
InstantOS 8.5 User Guide
Airheads Knowledgebase
Airheads Learning Videos
Aruba Central Documentation
ArubaOS Consolidated Release Notes
Aruba VIA ASE Solution - Configure VIA VPN
Search Airheads
cancel
Showing results for 
Search instead for 
Did you mean: